Manual Metabo Multi 260S (page 27 of 64) (English, German, Dutch, Danish)

451463

Zoom out

Zoom in

1/64

ENGLISH

− Tighten lock lever (70) again to

hold the saw blade in position.

3. If necessary use fence, sliding car-

riage or table extension.

4. Start motor.

5. Assume proper operating position.

6. Cut workpiece in a single pass.

7. Stop machine and lower the saw

blade guard fully, if no further cutting

is to be done immediately after-

wards.

Tips and Tricks

• Use roller supports on both sides of

the saw when cutting long stock.

• To simplify repetitive cut-off work

use a stock stop.

10.1 Setup



Danger!

Before setting the machine up:

− Switch machine OFF.

− Unplug.

− Wait until machine has come to a

complete stop.

Flat belt change

For operation as spindle moulder the flat

belt (72) must be positioned as illus-

trated:

If this is not the case, position it as fol-

lows.

1. Open the access door.

2. Loosen lock lever (73) and lift motor

slightly with handle (74).

3. Take the flat belt that is not required

off the motor pulley (75).

4. Tuck the flat belts (76) not required

behind the retaining springs as illus-

trated, so they do not interfere with

the drive belt on the pulleys.

5. Place the flat belt (72) on the cutter

spindle and on the motor pulley (75).



Caution!

In spindle moulder mode the

cutter spindle speed must be selec-

ted according to the cutter diameter!

Cutting speed in m/s



Danger!

At these combinations there is

an increased risk of kickback.

The speed is set by changing the flat

belt:

• small (= rear) motor pulley: (77)

speed of cutter spindle 4500 min

-1

• large (= front) motor pulley: (78)

speed of cutter spindle 7000 min

-1

6. Check direction of rotation of the

cutter spindle: Turn motor pulley by

hand in direction indicated by arrow

– the cutter spindle must rotate

clockwise (if viewed from top). If this

is not the case, take flat belt off the

cutter spindle and turn over.

7. Tighten the flat belt by pushing the

motor downward with the handle

(74).

8. Lock motor in position with the lock

lever (73).

9. Close access door.

Work area preparation

Ensure the removal of all not required

objects from the work area:

1. Saw blade and blade guard fully

retracted and covered by table

insert?

2. Rip fence dismounted?

3. Suction port disconnected from the

dust collector and lowered?

Cutter installation

1. Remove table insert and table insert

rings.

2. Loosen locking screw (79) and

crank cutter spindle with handwheel

(80) fully up.

3. To lock the cutter spindle, slide the

long lock pin (81) through the slot

into the hole provided in the cutter

spindle.

4. Loosen spindle nut (82) and remove

any fitted cutters and spacing col-

lars.

5. Fit new cutter and spacing collars on

the cutter spindle.



Caution!

− Observe direction of rotation of

the cutter (counter-clockwise if

viewed from top)!

− The cutter must be positioned on

the cutter spindle as far down

possible!

6. Cover the clearance zone around

the cutter spindle with table insert

rings that accommodate the cutter

head diameter.

7. Fill space between cutter and spin-

dle thread with spacing collars.

10. Spindle Moulder Mode

Cutter spindle-

speed (min

–1

)

4500 7000

Cutter

diameter (mm)

180 42 m/s 66 m/s

160

38 m/s 59 m/s

140



51 m/s

120



44 m/s

100



37 m/s

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 260S in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 3,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo Multi 260S Manual

Product: