451463

Metabo Multi 260S Manual

26
Zoom out
Zoom in
Previous page
1/64
Next page
26
ENGLISH
3. Replace the kerf plate. To do so,
slightly bend the table insert apart at
its rear and slide over saw blade
and riving knife. Then fit table insert
flush into the saw table.
Rip fence installation
• Slide fence carrier (59) on the guide
rail (60) and secure with clamping
plate (61).
Mitre fence installation
The mitre fence can be used both in
front of or behind the workpiece.
• When used in front of the
workpiece – especially suitable for
cutting ledges and boards:
:
• When used behind the workpiece –
especially suitable for cutting
sheets:
1. Loosen screws (62) until fence car-
rier can be pushed in the groove of
the sliding carriage.
2. Set to desired angle and tighten
screws (62).
3. Loosen screws (63), until fence
extrusion can be pushed on the
fence carrier (64).
4. Shift wooden end piece (65) to other
end, if necessary. The end piece
must be fitted on the end of the
fence extrusion that reaches to the
saw blade.
Caution!
The fence extrusion must not
extend into the line of cut!
5. Tighten screws (63).
9.2 Safety
Safety Devices
• Riving knife
The riving knife (66) prevents the work-
piece from being caught by the rising
teeth of the saw blade and being thrown
against the operator.
When sawing, the riving knife must be
positioned at a distance of 3 – 8 mm
from the saw blade
.
• Blade guard
The blade guard (67) protects against
accidental contact with the saw blade
and from chips flying about.
When using the saw, the blade guard
must alway be positioned so that the dis-
tance between the workpiece and lower
front edge of the blade guard is not more
then 2 mm.
• Push stick
The push stick (68) serves as an exten-
sion of the hand and protects against
accidental contact with the saw blade.
Always use push stick if distance
between
rip fence and saw blade is ≤ 120 mm.
Information for a safe operation
General Hazard:
− Never cut several workpieces at the
same time – and also no bundles
containing several individual pieces.
Risk of personal injury if individual
pieces are caught by the saw blade
uncontrolled.
Risk of kickback
Risk of injury by workpiece
kickback (workpiece is caught by the
rotating saw blade and thrown back
against the operator):
− Do not attempt to stop the saw
blade by pushing the workpiece
against its side.
− Always hold the workpiece down on
the table and do not jam it.
− always work with a properly set riv-
ing knife.
− Always use sharp saw blades. If in
doubt check workpiece for inclusion
of foreign objects (e.g. nails, screws,
lose knots).
Danger!
Drawing-in/trapping hazard!
− Use a feeding aid (push stick) if you
want to cut short stock.
− Never cut stock to which ropes,
cords, strings, cables and wires are
attached or which contains such
materials.
9.3 Operation
1. Set bevel angle:
− Loosen lock lever (69).
− Tilt the sawhead to obtain the
desired bevel angle.
− Tighten lock lever (69) to hold the
saw blade in position.
2. Set depth of cut:
− Loosen lock lever (70) and push
lever (71) down.
− Set desired depth of cut – the dis-
tance between workpiece and
lower front edge of the blade
guard must not be more than
2 mm.
59
61
60
62
63
64
65
6766
68
69
70
71
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo Multi 260S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 260S in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info