Manual Metabo Multi 260S (page 25 of 64) (English, German, Dutch, Danish)

451463

Zoom out

Zoom in

1/64

ENGLISH

with a suitable cleaning and mainte-

nance spray (optional accessory).

• Apply an anti-seize compound to all

planing bed surfaces afterwards.

This makes feeding easier and pro-

vides for a smoother surface finish.



Note:

Further information on installation

and operation is found in the operating

instructions supplied with the Drilling and

Morticing Attachment.



Danger!

Before setting the machine up:

− Switch machine OFF.

− Unplug.

− Wait until machine has come to a

complete stop.

Flat belt change

For operation with the Drilling and Mor-

ticing Attachment the flat belt (45) must

be put on as illustrated:

If this is not the case, the flat belt must

be positioned as detailed in chapter

"Surface Planer Mode".



Caution!

When using the Drilling and

Morticing Attachment the speed of

the chuck must be selected accor-

ding to the mortising bit diameter!

The speed is set by changing the flat

belt:

• small (= rear) motor pulley (48):

spindle speed 3900 min

-1

for mortising bits 10 mm ∅ and up

• large (= front) motor pulley (49):

spindle speed 6300 min

-1

for mortising bits up to 10 mm ∅

To adjust the speed:

1. Open the access door.

2. Loosen lock lever (46) and lift motor

slightly with handle (47).

3. Shfit motor along the axis of the

motorshaft: The motor pulley must

be in alignment with the cutter-

block’s pulley

4. Tighten flat belt by pushing the

motor downward with handle (47).

5. Lock motor in position with the lock

lever (46).

6. Close access door.

Adjusting the cutterblock cover:

7. Adjust cutterblock cover (50) so that

the cutterblock is completely cov-

ered.

9.1 Setup



Danger!

Before setting the machine up:

− Switch machine OFF.

− Unplug.

− Wait until machine has come to a

complete stop.

Flat belt change

For operation as circular saw the flat belt

(51) must be positioned as illustrated:

If this is not the case, position it as fol-

lows.

1. Open the access door.

2. Loosen lock lever (52) and lift motor

slightly with handle (53).

3. Take the flat belt that is not required

off the motor pulley (54).

4. Tuck the flat belts not required (55)

behind the retaining springs as illus-

trated, so they do not interfere with

the drive belt on the pulleys.

5. Place the flat belt for the saw spin-

dle on the large diameter (front) (51)

motor pulley (54).

6. Shift motor along the axis of the

motor shaft fully to the rear: The

large diameter motor pulley must be

in alignment with the pulley on the

saw spindle.

7. Tighten the flat belt by pushing the

motor downward with the handle

(53).

8. Lock motor in position with the lock

lever (52).

9. Close access door.

Work area preparation

Ensure the removal of all not required

objects from the work area:

1. Cutter fence completely dis-

mounted?

2. Cutter spindle fully retracted and

covered by table rings and insert?

3. Cutterblock cover lowered on the

table?

4. Suction port disconnected from the

dust collector and lowered?

Raising the saw blade

1. Remove table insert (56).

2. To raise the saw blade loosen lock

lever (57) and push lever (58) down-

ward. To lock blade at desired depth

of cut tighten lock lever (57) again.

8. Operation With The Drill-

ing And Morticing Attach-

ment (Optional Acces-

sory)

9. Circular Saw Mode

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 260S in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 3,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo Multi 260S Manual

Product: