451463

Metabo Multi 260S Manual

23
Zoom out
Zoom in
Previous page
1/64
Next page
23
ENGLISH
− Always plane the workpiece over its
entire length.
Risk of injury by touching the
rotating cutterblock:
− Always keep your hands well clear
of the cutterblock.
− When jointing, use the jointer
fence to provide firm support for
the workpiece. Use an auxiliary
fence when planing thin or nar-
row stock, to keep your hands at
a safe distance from the cutter-
block.
− Always cover the part of the cutter-
block that is not covered by the
workpiece with the cutterblock
cover.
− Adjust the cutterblock cover exactly
to the dimension of the workpiece.
− Never reach with your hands under
the cutterblock cover when guiding
the workpiece!
− Use workpiece supports (such as
table extensions) to keep long
stock from losing its balance.
− Plane only stock which rests
securely on the table.
− Use a feeding aid (push block) when
planing a small workpiece, which
can not be guided with a sufficient
safety distance to the cutterblock.
− Do not pull the workpiece back over
the unguarded cutterblock!
Risk of injury by cuts with the
cutterblock at standstill:
− Always cover the cutterblock with
the guard extrusion of the cutter-
block cover when the machine is not
used as thickness planer.
6.3 Operation
1. Place stock against the jointer fence
(29).
2. Adjust cutterblock guard extrusion
(30):
− Planing the face of a plank or work-
pieces up to 75 mm thick:
Use the adjusting screw (31) to
adapt the guard extrusion to the
height of the workpiece. When guid-
ing the workpiece, the hands slide
over the guard extrusion.
− when planing narrow edges (edge
jointing) or workpieces more than
75 mm thick:
Loosen adjusting screw (32) to
adapt the guard extrusion to the
width of the workpiece.
3. Adjust depth of cut with lever (33)
.
Note:
The max. chip removal in a single
pass is 4 mm.
4. The thicknesser feed can be
switched-off for surface planing. To
switch off, pull lever (34) out until it
engages.
5. Start motor.
6. Assume proper operating position:
position yourself to one side of the
infeed table.
7. Feed workpiece straight across the
infeed table, holding your fingers
close together, guiding the work-
piece with the palm of your hands.
8. Switch machine off if no further plan-
ing is to be done immediately after-
wards.
Workpiece dimensions
• Width: max. 259 mm.
• Thickness: at least 4 mm more than
the set planing thickness.
Tips and tricks
• Plane stock with the grain, if possi-
ble.
• Use roller supports on both sides of
the planer/thicknesser when work-
ing long stock.
• It is better to make several passes
with less chip removal, than making
only a few passes with a high depth
of cut.
• When surface planing a warped
(twisted) board, place on infeed
table with the hollow side facing
down.
• When surface planing short work-
pieces:
− use push stick;
− feed workpiece with the small
face first;
− guide workpiece turned approx.
20° against the direction of feed.
• Keep surfaces of planing beds clean
– in particular, remove resin residue
with a suitable cleaning and mainte-
nance spray (optional accessory).
• Apply an anti-seize compound to all
planing bed surfaces afterwards.
This makes feeding easier and pro-
vides for a smoother surface finish.
7.1 Setup
Danger!
Before setting the machine up:
− Switch machine OFF.
− Unplug.
− Wait until machine has come to a
complete stop.
Flat belt change
For operation as planer the flat belt (35)
must be positioned as illustrated:
If this is not the case, the flat belt must
be positioned as detailed in chapter
"Surface Planer Mode".
29
31
30
32
33
34
7. Thickness Planer Mode
35
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo Multi 260S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 260S in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info