451463

Metabo Multi 260S Manual

29
Zoom out
Zoom in
Previous page
1/64
Next page
29
ENGLISH
7. Use a push block when working the
ends of narrow stock.
8. When working across the grain
(making slots and tenons), use ten-
oning table, stock clamp (92) and
sliding carriage (93).
Note:
Further information on installation
and operation is found in the operating
instructions supplied with the Tenoning
Table.
9. Switch machine off if no further plan-
ing is to be done immediately after-
wards.
Tips and Tricks
• Always make several passes if a
large amount of material needs to
be removed.
• Make trial cuts on a piece of scrap
before working the actual work-
piece.
• When working complex shapes,
make jigs and guides to guide the
workpiece properly.
Danger!
Prior to all servicing:
− Switch machine OFF.
− Unplug.
− Wait until machine has come to a
complete stop.
Replace defective parts, especially of
safety devices with genuine replace-
ment parts only. Parts not tested and
approved by the equipment manufac-
turer can cause unforeseen damage.
After all servicing:
− Check to see that all safety
devices are operational.
− Make sure that no tools or other
parts remain on or in the
machine.
Repair and maintenance work other
than described in this section should
only be carried out by qualified speci-
alists.
11.1 Replacing cutter knives
Note:
Worn cutter knives are noticeable
by
− reduced planing performance;
− increased risk of kickback;
− motor overloads.
Danger!
Risk of personal injury by cuts
from the cutter knives! Wear gloves
when changing cutter knives.
To remove the cutter knives:
1. Unplug power cable.
2. Remove the fence.
3. Remove the cutterblock cover
4. Turn the three square-head bolts
(94) of the cutter knife lockbar (95)
all the way in (wear gloves!).
5. At first remove cutter knife (96), then
cutter knife lockbar (95) from the
cutterblock (97).
6. In the cutterblock’s groove there are
still two springs. Note exact position
of the springs (for reassembly), then
remove them.
7. Clean all surfaces of cutterblock and
cutter knife lockbar with a suitable
solvent.
Danger!
Do not use cleaning agents
(e.g. to remove resin residue) that
could corrode the light metal compo-
nents; the stability of the light metal
components would be adversely
affected.
To install the cutter knives:
Danger!
− Use only suitable cutter knives
conforming to EN 847-1 (see
"Available Accessories") – unsui-
table, incorrectly mounted, blunt
or damaged cutter knives can
work loose or increase the risk of
kickback considerably respec-
tively.
− Always replace both cutter
knives.
− On the cutterblock and cutter
knife lockbar the numbers "1"
and "2" respectively are punched
in. When reassembling, ensure
that the numbers on cutterblock
and cutter knife lockbar match,
otherwise damage to the bearings
could occur by a balance error.
− Only cutter knives marked "HSS"
or "HS" can be resharpened!
When resharpening, remove the
same amount of material from
both cutter knives, otherwise a
balance error may cause damage
to the bearings.
− Cutter knives can only be reshar-
pened down to a minimum width
of 12 mm.
− Install cutter knives using only
genuine replacement parts.
8. Place spring clips back into their ori-
ginal position in the cutterblock’s
groove.
9. Place the cutter knife lockbar in the
cutterblock’s groove. Turn the three
square-head bolts so far out that the
cutter knife will just slide in.
10. Insert a sharp cutter knife and adjust
position with the cutter knife lockbar,
so that neither protrudes over the
edge of the cutterblock.
11. Place cutter knife setting gauge on
planer bed in the direction as indi-
cated by the arrows in the illustra-
tion:
The setting gauge (98) must rest
with its edge (99) on the front edge
of the infeed table (100).
The pin (101) of the setting gauge
must engage in the cutterblock’s
groove.
The cutter knife (102) must protrude
11. Care and Maintenance
92 93
949596
97
98 99
100
101
102
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo Multi 260S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 260S in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info