Manual Metabo Multi 260S (page 31 of 64) (English, German, Dutch, Danish)

451463

Zoom out

Zoom in

1/64

ENGLISH

For special tasks the following accesso-

ries are available at your specialized

dealer – see back cover for illustrations:

A Drilling and Morticing Attachment

for drilling mortices of max. 100 mm

depth and max. 100 mm long.

B Table Extension

required for working long stock.

C Sliding Carriage Side Extension

required to work wide stock.

D Stock Stop

required for repetitive cut-off work.

E Tenoning Table

required for unproblematic tenon-

ing.

F Curved Moulding Stop

required for the exact guiding of

curved stock.

G HS Cutter Knives

260x20x2.5

for extended edge life. Resharpen-

able.

H TCT Saw Blade

250x3.2/2.2x30 24 ATB

for rip and crosscuts in grown tim-

ber and particle board.

I TCT Saw Blade

250x3.2/2.2x30 48 UAT

for rip and cross cuts in panels,

plastics, aluminium and high-quality

veneered sheets.

J TCT Saw Blade

250x3.2/2.2x30 60 combination

ATB

General purpose saw blade for

plastics and non-ferrous metals.

K TCT Saw Blade

250x3.2/2.2x30 80 trapezoidal flat

teeth

General purpose saw blade for

plastics and non-ferrous metals.

L Ball Transfer Stand

for exact guiding of long stock.

Used with either swivel ball or roller

head.

M WAXILIT Anti-seize Compound

improves stock gliding quality on

the planing beds.

N Care and Maintenance Spray

to remove resin residue and for pre-

serving the metal surfaces.



Danger!

Repairs to electric tools must

be carried out by qualified electrici-

ans only!

Electric tools in need of repair can be

sent to the service centre of your coun-

try. Refer to the spare parts list for the

address.

Please attach a description of the fault to

the electric tool.

The machine's packaging can be 100 %

recycled.

Worn out machines and accessories

contain considerable amounts of valua-

ble raw and plastic materials, which can

be recycled.

These instructions are printed on chlo-

rine-free bleached paper.



Danger!

Prior to any servicing:

− Switch Off.

− Unplug.

− Wait until machine has come to a

complete stop.

Check to see that all safety devices are

operational after any servicing.

15.1 All operating modes

Motor does not run

No supply voltage.

− Check cables, plug, outlet and

mains fuse.

Access door not closed.

− Close access door.

ON/OFF switch locked.

− Unlock ON/OFF switch by turning

clockwise.

Undervoltage relay tripped by tempo-

rary voltage failure.

− Start again.

Motor has overheated, e.g. due to blunt

cutting tools, overloading or chip

buildup.

− Remove cause for overheating and

allow to cool down for approx. 10

minutes, then start again.

15.2 Surface/thickness planer

Performance lessens

Cutter knives blunt.

− Install sharp knives.

Flat belt slips.

− Re-tension flat belt.

Planed surface not smooth

Cutter knives blunt.

− Install sharp knives.

Cutter knives blocked by chips.

− Remove chips.

Moisture contents of workpiece too high.

− Dry workpiece.

Planed surface cracked

Cutter knives blunt.

− Install sharp knives.

Cutter knives blocked by chips.

− Remove chips.

Workpiece was planed against the grain.

− Plane workpiece in opposite direc-

tion.

Too much material removed in one pass.

− Make several passes at less depth

of cut.

Worked surface uneven

Cutter knives are installed unequal.

− Adjust cutter knives with setting

gauge.

Feed rate too little (thicknessing)

Resin buildup on thicknesser bed.

− Clean thicknesser bed and apply

light coat of anti-seize compound.

Feed rollers stiff.

− Repair feed rollers.

Flat belt slips.

− Re-tension flat belt.

Workpiece jams

(thicknessing)

Too much material removed in one pass.

− Make several passes at less depth

of cut.

15.3 circular saw

Loss of cutting performance

Saw blade blunt (possibly tempering

marks on blade body)

− Replace saw blade.

Flat belt slips.

− Re-tension flat belt.

Sliding carriage stiff:

Guide elements dirty.

− Clean guide elements with brush,

compressed air or dust collector.

15.4 Spindle moulder

Performance lessens

Cutter blunt.

− Replace cutter.

Flat belt slips.

− Re-tension flat belt.

Blocked dust port

No dust collector hooked up:

− connect dust collector.

Dust build-up around the cutter spindle.

− Remove table insert rings, move

cutter spindle up and down and

clean surroundings with brush or

compressed air and dust collector.

Sliding carriage stiff:

Guide elements dirty.

− Clean and lubricate guide elements.

12. Available Accessories

13. Repairs

14. Environmental Protection

15. Trouble Shooting

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 260S in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 3,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo Multi 260S Manual

Product: