657614
30
Zoom out
Zoom in
Previous page
1/129
Next page
30
a
Dismounting wheels
To dismount the wheel release the four bolts which en-
sure the fixing of the axle to the fork by two to three turns.
Do not unscrew the bolts completely. Subsequently, re-
lease the counterpart of the axle/bolt cap and remove
the axle completely from the hub.
i
More information are provided at
www.marzocchi.com
Marzocchi 15mm QR (e.g. Marzocchi 350CR)
Mounting wheels
If your bike is equipped with a Marzocchi 15mm QR sys-
tem
(a)
, put the front wheel into the fork and mount the
rotor in the brake caliper.
Bring the front wheel into the right position between the
drop-outs. Insert the thru axle with the E-Thru quick-re-
lease lever open from the right through the drop-out and
the hub.
As soon as the axle thread engages with the thread of
the left fork leg, close the axle by turning it clockwise.
In doing so, keep hold of the counter nut on the left fork
side. During the first rotations you should be able to ro-
tate the thru axle nearly without resistance. Tighten the
axle a little.
Close the Marzocchi quick-release lever like a usual
quick-release lever.
At the beginning you should feel virtually no resistance
and clamping effect. When the lever is at right angle the
resistance you feel should increase significantly and to-
wards the end you should need even more strength to
close the lever.
If you do not succeed in closing the lever completely,
open it again. Keep hold of the nut and turn the axle a
little counterclockwise. Try again to close the quick-re-
lease lever.
Use the palm of your hand to push it in all the way while
your fingers pull on the fork leg, but not on a spoke.
In its end position the quick-release lever should be
tight so that it can no longer be turned. Make sure the
quick-release lever does not stand out to the front or to
the side and does not touch the fork. The best closing
position is in nearly upright position in front of the lower
leg.
Dismounting wheels
If your bike is equipped with a Marzocchi 15mm QR sys-
tem, open the quick-release lever completely. Hold the
nut on the left side tight and turn the thru axle counter-
clockwise.
Once you have screwed out completely the thru-axle
thread from the thread of the lower leg, you can remove
the thru axle completely.
i
More information are provided at
www.marzocchi.com
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Merida Pedelec at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Merida Pedelec in the language / languages: English as an attachment in your email.

The manual is 3,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info