684233

McCulloch CS 42S Manual

13
Zoom out
Zoom in
Previous page
1/536
Next page
BUCKING WITHOUT A SUPPORT
1. Overcut through 1/3 of the diameter of the log.
2. 5ROOWKHORJRYHUDQG¿QLVKZLWKDVHFRQGRYHUFXW
NOTE: Watch for logs with a compression side to
prevent the saw from pinching.
BUCKING USING A LOG OR SUPPORT
STAND
1. 0DNHWKH¿UVWFXWRQWKHFRPSUHVVLRQVLGHRIWKH
ORJ<RXU¿UVWFXWVKRXOGH[WHQGRIWKHGLDPHWHU
of the log.
2. Finish with your second cut.
LIMBING AND PRUNING
a WARNING! Be alert for and guard against
kickback. Do not allow the moving chain to
contact any other branches or objects at
the nose of the guide bar when limbing or
pruning. Allowing such contact can result in
serious injury.
a WARNING! Never climb into a tree to limb or
prune. Do not stand on ladders, platforms, a
log, or in any position which can cause you
to lose your balance or control of the saw.
IMPORTANT POINTS
 :RUNVORZO\NHHSLQJERWKKDQGV¿UPO\JULSSHGRQ
the saw. Maintain secure footing and balance.
 Watch out for springpoles. Springpoles are small
size limbs which can catch the saw chain and
whip toward you or pull you off balance. Use
extreme caution when cutting small size limbs or
slender material.
 Be alert for springback. Watch out for branches
that are bent or under pressure. Avoid being
struck by the branch or the saw when the tension
LQWKHZRRG¿EHUVLVUHOHDVHG
 .HHSDFOHDUZRUNDUHD)UHTXHQWO\FOHDU
branches out of the way to avoid tripping over
them.
LIMBING
Always limb a tree after it is cut down. Only then can
limbing be done safely and properly.
Leave the larger limbs underneath the felled tree to
support the tree as you work.
Start at the base of the felled tree and work toward the
top, cutting branches and limbs. Remove small limbs
with one cut.
Keep the tree between you and the chain. Cut from
the side of the tree opposite the branch you are
cutting.
Remove larger, supporting branches with the cutting
WHFKQLTXHVGHVFULEHGLQ%8&.,1*:,7+287$
SUPPORT.
Always use an overcut to cut small and freely hanging
limbs. Undercutting could cause limbs to fall and pinch
the saw.
PRUNING
a WARNING! Limit pruning to limbs shoulder
height or below. Do not cut if branches
are higher than your shoulder. Get a
professional to do the job.
1. 0DNHWKH¿UVWFXWRQHWKLUGRIWKHZD\WKURXJKWKH
bottom of the limb.
2. Make the second cut all the way through the limb.
3. Make the third overcut leaving a 2.5 to 5
FHQWLPHWHUWRLQFKFROODUIURPWKHWUXQNRIWKH
tree.
13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch CS 42S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch CS 42S in the language / languages: All languages as an attachment in your email.

The manual is 20,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info