Manual McCulloch CS 42S (page 11 of 536) (All languages)

684233

Zoom out

Zoom in

1/536

front handle with your left hand.

2. Hold the chainsaw approximately 40-45

FHQWLPHWHUVLQFKHVDERYHDVWXPSRURWKHU

wooden surface.

3. Release your grip on the front handle and use the

weight of the saw to let the tip of the guide bar fall

forward and contact the stump. When the tip of the

bar hits the stump, the brake should activate.

WORKING TECHNIQUES

PRACTICING YOUR CUTS

Practice cutting a few small logs using the following

WHFKQLTXHVWRJHWWKH³IHHO´RIXVLQJ\RXUVDZEHIRUH

you begin a major sawing operation.

 6TXHH]HWKHWKURWWOHWULJJHUDQGDOORZWKHHQJLQHWR

reach full speed before cutting.

 Begin cutting with the saw frame against the log.

 Keep the engine at full speed the entire time you are

cutting.

 Allow the chain to cut for you. Exert only light

downward pressure. If you force the cut, damage to

the guide bar, chain, or engine can result.

 Release the throttle trigger as soon as the cut

is completed, allowing the engine to idle. If you

run the saw at full throttle without a cutting load,

unnecessary wear can occur to the chain, guide

bar, and engine. It is recommended that the engine

not be operated for longer than 30 seconds at full

throttle.

 To avoid losing control when cut is complete, do not

put pressure on saw at end of cut.

 Stop the engine before setting the saw down after

cutting.

FELLING A TREE

PLANNING

a WARNING! Check for broken or dead

branches which can fall while cutting

causing serious injury. Do not cut near

buildings or electrical wires if you do not

know the direction of tree fall, nor cut at

night since you will not be able to see well,

nor during bad weather such as rain, snow,

or strong winds, etc. If the tree makes

contact with any utility line, the utility

FRPSDQ\VKRXOGEHQRWL¿HGLPPHGLDWHO\

Carefully plan your sawing operation in advance.

Clear the work area. You need a clear area all around

the tree so you can have secure footing.

The chainsaw operator should keep on the uphill side

of the terrain as the tree is likely to roll or slide downhill

after it is felled.

Study the natural conditions that can cause the tree to

fall in a particular direction.

Natural conditions that can cause a tree to fall in a

particular direction include:

 The wind direction and speed.

 The lean of the tree. The lean of a tree might not be

apparent due to uneven or sloping terrain. Use a

plumb or level to determine the direction of tree lean.

 Weight and branches on one side.

 Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted, it can

snap and fall toward the operator. Check for broken or

dead branches which can fall on you while cutting.

Make sure there is enough room for the tree to fall.

Maintain a distance of 2-1/2 tree lengths from the

nearest person or other objects. Engine noise can

drown out a warning call.

Remove dirt, stones, loose bark, nails, staples, and

wire from the tree where cuts are to be made.

Plan a clear retreat path to the rear and diagonal to

WKHOLQHRIIDOO1RWHWKHGDQJHU]RQHUHWUHDWSDWK

DQGIHOOLQJGLUHFWLRQLQWKHIROORZLQJGLDJUDP

USING THE NOTCH METHOD

The notch method is used to fell large trees. A notch

is cut on the side of the tree in the desired direction of

fall. After a felling cut is made on the opposite side of

tree, the tree will tend to fall into the notch.

NOTE: If the tree has large buttress roots, remove

them before making the notch. If using saw to

remove buttress roots, keep saw chain from

contacting ground to prevent dulling of the chain.

Make the notch cut by cutting the top of the notch

¿UVW&XWWKURXJKRIWKHGLDPHWHURIWKHWUHH1H[W

complete the notch by cutting the bottom of the notch.

Once the notch is cut remove the notch of wood from

the tree.

After removing the wood from the notch, make the

felling cut on the opposite side of the notch. This is

GRQHE\PDNLQJDFXWDERXWFHQWLPHWHUVLQFKHV

higher than the center of the notch. This will leave

enough uncut wood between the felling cut and the

notch to form a hinge. This hinge will help prevent the

tree from falling in the wrong direction.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch CS 42S in the language / languages: All languages as an attachment in your email.

The manual is 20,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch CS 42S Manual

Product: