778510
8
Zoom out
Zoom in
Previous page
1/22
Next page
Zorg ervoor dat de STOP / RUN-schakelaar in de RUN-positie staat (Pics.5) (5.1).
Houd de grondboor stevig met één hand ingedrukt. Pak met de andere hand de handgreep van
het startkoord vast (Afb.6) en trek langzaam totdat u weerstand voelt die aangeeft dat de terug-
loopstarter is ingeschakeld.
Trek bij weerstand krachtig aan het koord.
Ga door met deze procedure totdat de motor start.
Als de motor succesvol is gestart en soepel loopt, zet u de chokehendel terug in de stand UIT.
Druk de hendel van de veiligheidsschakelaar in (Afb.5) (5.2) en knijp vervolgens de gashendel in
(Afb.5) (5.3), het boorbit begint te draaien. Om de boorsnelheid aan te passen, draait u de
snelheidsregelaar (Afb.5) (5.4) totdat de gewenste instelling is bereikt.
Om te voorkomen dat het boorbit gaat draaien. Knijp kort in en laat de gashendel los.
BEDIENING VAN DE GRONDBOOR
Dit product vereist het gebruik van twee handen om een veilige bediening te garanderen.
Zorg ervoor dat bij het boren van gaten geen risico bestaat op contact met elektrische kabels,
gasleidingen, waterleidingen enz. Raadpleeg de plaatselijke autoriteiten voordat u begint.
Inspecteer het werkgebied voordat u begint. Verwijder alle voorwerpen of vuil dat kan worden
weggeslingerd, vastlopen of verstrikt raken in het boorbit.
Neem een stabiele houding aan en houd de grondboor altijd voor uw lichaam. Pak de handgre-
pen met beide handen vast en zorg ervoor dat u de bedieningshendels veilig kunt bedienen.
Laat het boorbit op volle snelheid komen voordat u met het boren begint.
Als de boor een steen, harde grond enz. raakt, kan de rotatie onmiddellijk stoppen en een harde
koppelreactie geven. Het is daarom vereist dat de bediener beide handgrepen stevig vasthoudt
tijdens het gebruik om een plotselinge koppelreactie te compenseren.
Verwijder eventueel vastzittend vuil van het boorbit en onderzoek het op eventuele schade
voordat u weer aan het werk gaat.
DE MOTOR STOPPEN (PIC.7)
Schuif de STOP / RUN-schakelaar naar de STOP-positie (Afb.7) (7.1)
Make sure that the STOP/RUN switch is in the RUN position (Pics.5) (5.1).
Hold down the hole borer firmly with one hand. With the other hand grip the recoil starter cord
handle (Pic.6) and pull slowly until resistance is felt indicating that the recoil starter is engaged.
When resistance is felt pull the cord sharply.
Continue this procedure until the engine starts.
When the engine has been successfully started and is running smoothly return the choke lever to the OFF
position.
Press in the safety switch lever (Pic.5)(5.2) then squeeze the throttle lever (Pic.5)(5.3), the auger bit will
begin to rotate. To adjust the boring speed rotate the speed adjuster (Pic.5)(5.4) until the desired setting is
achieved.
To stop the auger bit from rotating. briefly squeeze then release the throttle lever.
OPERATING THE HOLE BORER
This product requires the use of two hands to ensure safe operation.
Make sure that the hole boring operation does not involve the risk of contact with electric cables, gas
mains, water pipes etc. Check with local authorities prior to commencing.
Inspect the work area before starting. Remove any objects or debris that could be thrown, jammed or
become entangled in the auger bit.
Adopt a stable stance always keeping the hole borer in front of your body. Grip the handles with both
hands ensuring you can safely operate the control levers.
Allow the auger bit to reach full speed before commencing the boring operation.
If the auger bit hits a stone, hard ground etc., the rotation may stop immediately and give a hard torque
reaction.
It is therefore required that the operator has a firm grip on both handles during operation in order to
compensate for a sudden torque reaction.
Remove any jammed debris from the auger bit and examine for any damage before re- commencing work.
STOPPING THE ENGINE (PIC.7)
Push the STOP/RUN switch to the STOP position (Pic.7)(7.1)
MAINTENANCE
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxxtools 20570 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxxtools 20570 in the language / languages: English, Dutch as an attachment in your email.

The manual is 2.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info