778510
20
Zoom out
Zoom in
Previous page
1/22
Next page
LUBRICATING THE GEARBOX (PIC. 10)
It is recommended that after 50 hours of use the gearbox oil should be replaced using suitable 3#
Lithium Grease. Remove the drain plug
(Pic.10)(10.2) on the side of the gearbox then tilt the engine so all the oil drains from the gearbox.
With the engine in its upright position add Gear grease. Ret the drain plug.
STORAGE
If the hole borer is not to be used or is to be stored for more than one month the following storage
procedure should be carried out. Drain all the fuel from the fuel tank and the carburetor, ensure
that all the fuel has been removed.
Remove the spark plug and pour approximately one tablespoon full of clean engine oil into the
spark plug hole. With the ignition turned OFF gently pull on the recoil starter cord several times.
Re-t the spark plug continue to pull the recoil starter cord until the piston is on the compression
stroke (when resistance is felt) then stop puling.
Store the hole borer in a dry well ventilated place under a cover to prevent any dust or debris from
accumulating on the hole borer.
TECHNICAL SPECIFICATIONS
Sound intensity level for the operator may exceed 85dB(A) & sound protection measures are
necessary.
LUBRICATING THE GEARBOX (PIC. 10)
It is recommended that after 50 hours of use the gearbox oil should be replaced using suitable 3# Lithium
Grease. Remove the drain plug
(Pic.10)(10.2) on the side of the gearbox then tilt the engine so all the oil drains from the gearbox. With
the engine in its upright position add Gear grease. Refit the drain plug.
STORAGE
If the hole borer is not to be used or is to be stored for more than one month the following storage
procedure should be carried out. Drain all the fuel from the fuel tank and the carburetor, ensure that all
the fuel has been removed.
Pic. 9
9.1
Pic. 10
10.2
Remove the spark plug and pour approximately one tablespoon full of clean engine oil into the spark plug
hole. With the ignition turned OFF gently pull on the recoil starter cord several times. Re-fit the spark
plug continue to pull the recoil starter cord until the piston is on the compression stroke (when resistance
is felt) then stop puling.
Store the hole borer in a dry well ventilated place under a cover to prevent any dust or debris from
accumulating on the hole borer.
TECHNICAL SPECIFICATIONS
Sound intensity level for the operator may exceed 85dB(A) & sound protection measures are necessary.
MODEL 20570
Engine type Air-cooled 2 stroke, 1E44F, Single Cylinder Petrol Engine
Displacement 51.7 cm3
Fuel Unleaded petrol
Fuel/Oil mix ration 25:1
Fuel tank capacity 1L
Gearbox oil capacity 250mL
Gearbox oil type 3# Lithium Grease
Starting system Recoil starter
Air cleaner type Sponge element
Auger bit 80cm x 80mm, 80cm x 150mm, 80cm x 200mm, 30cm
extension rod
Weight 20kg / 19kg
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxxtools 20570 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxxtools 20570 in the language / languages: English, Dutch as an attachment in your email.

The manual is 2.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info