650499
8
Zoom out
Zoom in
Previous page
1/14
Next page
PX502 Tape Library Quick Start Guide
8
3 Secure the back of the library to the rack with two
mounting clamps and two Allen screws on each clamp.
The mounting clamps are oriented differently
depending on the depth of the rack (see figure 10
).
4 Secure the mounting clamps to the rack rails with two
PHILLIPS screws on each side (see figure 10
).
Figure 10 Securing the Back of
the Library
5 To install the tape drives into the library:
a Remove the tape drive cover plates (if necessary,
some libraries ship with one tape drive installed) by
loosening the captive screws securing the plate to
the library chassis (see figure 11
).
Figure 11 Removing the Tape
Drive Cover Plates
N
OTE: If the rack depth is 27 to 30 in., the long portion
of the clamp is mounted to the back. If the rack
depth is 30 to 36 in., the long portion is mounted
to the front.
Right-hand back
bracket shown.
Allen
screws
Long
portion
Cover plate
Tape
drive
bay 1
Tape drive
bay 2
b Insert the tape drive(s) into the drive bay(s) slowly
until the connectors are seated. Refer to figure 12 for
drive bay numbering (see the
Quantum PX500 Series
Tape Drive Installation Instructions
PN 81-81301 for
information).
Figure 12 Installing the Tape
Drives
c Tighten the tape drive thumbscrews using a flat
blade screwdriver.
d Repeat these steps to install another tape drive in a
different location, if desired.
The library chassis is installed in the rack.
Cabling the Library
0
1 Connect the SCSI cables and jumpers as shown in the
following figures:
Figure 13 SCSI System Controller Board
Figure 14 Surrogate SCSI System Controller Board
Figure 15 Native Fibre Channel System Controller
Board
NOTE: Quantum ships sufficient SCSI cables and
terminators with the libraries to set up two-drives
per SCSI bus. One tape drive per SCSI bus may be
necessary for optimum performance. Refer to
your tape drive documentation.
N
OTE: SCSI cable lengths should not exceed:
39.37 feet (12 meters) between the host and
the library for single drive per bus installations.
Tape
drive 2
Tape
drive 1
Back of Library
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxdata Quantum PX502 Tape Library at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxdata Quantum PX502 Tape Library in the language / languages: English as an attachment in your email.

The manual is 1,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info