650499

Maxdata Quantum PX502 Tape Library Manual

12
Zoom out
Zoom in
Previous page
1/14
Next page
PX502 Tape Library Quick Start Guide
12
Table 5 Setting Up the Cabinet
Setting the Date and Time
0
To set the date and time:
1 From the Setup screen, use the up and down arrows to
highlight Date and Time and press Enter.
The Date and Time screen displays (see figure 21
):
Figure 21 Date and Time Screen
The Date and Time screen displays the following
information about the library:
Cabinet Options Description
Host bus Sets the SCSI ID for both the
library and tape drives.
Stack role Assigns the library stack role
as Master, Slave, or Stand
alone (solo). There can be only
one Master library in a
multiple stack. Once
configured as a slave, all
library OCP functions can be
controlled via the Master
library OCP. The library model
number will also change to
PX500S indicating a stacked
library configuration. The
library model number is
available from the home
screen on the Master library
OCP.
Left load port Enables or disables the left
load port
Right load port Enables or disables the right
load port
Drive FUP from tape Allows you to perform a tape
drive firmware update from a
firmware update tape
cartridge.
2 Use the up and down arrows to view or edit the date
and time information. Press Enter to accept the new
settings.
3 When you are finished viewing/editing the date and
time information, press Exit to return to the Setup
screen.
Setting Network Information
0
To view or edit the network information:
1 From the Setup screen, use the up and down arrows to
highlight Network and press Enter.
The Network screen displays (see figure 22):
Figure 22 Network Screen
The Network screen allows you to view or edit the
following network settings:
• DHCP (default setting)
• IP address
• Subnet mask
•Default gateway
2 Use the up and down arrows to select the network
setting you wish to view or edit and press Enter.
When you are finished viewing/editing the network
information, press Back to return to the Setup screen.
3 For the network information such as the IP address to
be active, you must reboot the library by holding down
the power button located on the front of the library
(see figure 16).
The library shuts down.
4 Push the power button to start the library.
The PX502 tape library is initially configured and ready
for use.
N
OTE: The library must be offline to change these
settings.
… 12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxdata Quantum PX502 Tape Library at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxdata Quantum PX502 Tape Library in the language / languages: English as an attachment in your email.

The manual is 1,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info