Manual Makita DCU180 (page 19 of 116) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

690917

Zoom out

Zoom in

1/116

19 ENGLISH

NOTE: You can check the remaining battery capacity

even if the lock key is not inserted.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.30: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Control panel

►Fig.31: 1. Power button 2. Forward/reverse button

3. Speed button

To turn the power on, press the power button for a few

seconds. Press the forward/reverse button to switch

between the forward mode and reverse mode. Press

the speed button to switch between low speed and high

speed. When the power is turned on, the forward mode

and low speed are set. To turn the power off, press the

power button for a few seconds.

NOTE: The forward/reverse button is not available

while pulling the switch trigger.

NOTE: A short beep sound comes out when operat-

ing the machine in reverse.

NOTE: The speed button is not available when oper-

ating the machine in reverse.

Switch and brake action

WARNING: Before installing the battery car-

tridge into the machine, always check to see that

the switch trigger actuates properly and returns

to the "OFF" position when released.

To start the machine, pull the switch trigger. To stop the

machine, release the switch trigger and pull the brake

lever. To lock the brake lever, press the lock button

while pulling the brake lever. To release the lock, pull

the brake lever.

►Fig.32: 1. Switch trigger

►Fig.33: 1. Lock button 2. Brake lever

Rear wheel brake

The rear wheel on the left side is equipped with a brake.

Press the brake pedal toward the front to lock the brake.

To release the brake, press the brake pedal toward the

rear.

►Fig.34: 1. Pedal

Lighting up the front lamps

Press the lamp button on the battery box to light up

the lamps. To turn off the lamps, press the lamp button

again.

►Fig.35: 1. Lamp button 2. Lamp

NOTE: The lamps go off if the machine is left unat-

tended for approximately 10 minutes.

NOTE: The lamps go off when the power is turned off.

NOTE: You can light up the lamps even if the lock key

is not inserted.

Adjusting the handle height

Remove the short hexagonal bolts and shoulder bolts

using the wrench included in the package, and then

adjustthehandleheight.Theheightcanbeadjustedto

three levels. Tighten the shoulder bolts and short hex-

agonalboltstoxthehandle.

►Fig.36: 1. Short hexagonal bolt 2. Shoulder bolt

NOTICE: Fix the left and right handles at the

same height.

NOTICE: Do not tighten the short hexagonal

bolts with excessive force. Tighten them with

proper force so that the handles are stably xed.

NOTICE: Do not pinch the cords with the bolts.

Adjusting the width of the rear

wheels

Loosen the short hexagonal bolts using the wrench

included in the package, and then slide the rear wheels.

►Fig.37: 1. Rear wheel

Tighten the short hexagonal bolts using the wrench

includedinthepackagetoxthewheels.

►Fig.38: 1. Short hexagonal bolt

CAUTION: Extend the rear wheels to the max-

imum to keep balance. When the rear wheels are

not extended, keep the load to a minimum.

NOTICE: Fix the rear wheels at the same position

on both sides.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DCU180 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 20,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DCU180 Manual

Product: