657979

Makita AN935H Manual

11
Zoom out
Zoom in
Previous page
1/84
Next page
11 ENGLISH
3. Turntheadjustshaftandsetthestepofthe
changeplatesuitableforthenaillength.Makesurethat
the arrow points to the corresponding graduation incre-
mentofthenaillengthmarkedontheadjustshaft.
►Fig.14: 1.Changeplate2.Adjustshaft3. Arrow
NOTICE:Ifthetoolisoperatedwiththechange
platesettothewrongstep,itmayresultinpoornail
feedingortoolmalfunction.
4. Place the nail coil over the change plate and
uncoil enough nails to reach the nail rail.
Thenplacetherstnailinthenailrailandthesecond
nailinthefeedclaw.Also,placeotheruncoilednailson
feederbody.
►Fig.15: 1. Nail rail 2. Feed claw
5. Checkthatthenailcoilissetproperlyinthe
magazine.
6. Closethemagazinecapcarefully.Thenwith
depressingthelatchlever,closethedooruntilthelatch
lever locks.
Connecting air hose
CAUTION: Do not connect the air hose with
a nger on the trigger. An unexpected driving will
causeseriousinjury.
►Fig.16: 1.Airtting2. Air socket
Sliptheairsocketoftheairhoseontotheairttingon
thenailer.Besurethattheairsocketlocksrmlyinto
positionwheninstalledontotheairtting.
A hose coupling must be installed on or near the tool in
such a way that the pressure reservoir will discharge at
the time the air supply coupling is disconnected.
Changing the trigger for contact
actuation mode
CAUTION: Always disconnect the air hose
and unload the tool with nails before replacing
the trigger.
CAUTION: After the trigger replacement,
always check that the tool operates properly
before actual work. Do not load the tool with any
nails before checking the function to avoid unex-
pected nailing.
Thetriggerforsinglesequentialactuationmodeis
factory-installed.Tochangethenailingmodetocontact
actuation,replacethetriggerpartwiththeoneforcon-
tact actuation.
►Fig.17: 1.Triggerforcontactactuation2. Silver part
3.Triggerforsinglesequentialactuation
4. Black part
1. Turnthetriggerlocklevertothelockposition
.
►Fig.18: 1.Triggerlocklever
2. Pushthepinsecuringthetriggerfromtheure-
thanewasherside,andthenremovetheurethane
washer.Thenpulloutthepinandremovethetrigger.
►Fig.19: 1. Pin 2. Urethane washer 3.Trigger
3. Setthetriggerassemblyforcontactactuation.
Withpushinginthehingedpartinward,setthetrigger
sothatthehingedpartisundertherodofthevalvein
the housing.
►Fig.20: 1. Hinged part 2.Rodofthevalve
4. Insert the pin to the hole and secure it by urethane
washer.
5. Connecttheairhose,andmakesurethatthe
tooloperatesproperly.Refertothesection“Checking
properactionbeforeoperation”.
NOTE:Tosetbacktosinglesequentialactuation,
followtheproceduresforchangingthetriggerabove.
OPERATION
CAUTION: Make sure all safety systems are in
working order before operation.
CAUTION: When operating the tool, do not
close the face to the tool. Also keep hands and
feet away from the ejection port area.
CAUTION: When not operating the tool,
always lock the trigger by turning the trigger lock
lever to the lock position .
CAUTION: Make sure that the trigger is
locked when the trigger lock lever is set to the
lock position .
Checking proper action before
operation
Beforeoperation,alwayscheckfollowingpoints.
— Make sure that the tool does not operate only by
connecting the air hose.
— Make sure that the tool does not operate only by
pulling the trigger.
— Make sure that the tool does not operate only by
placing the contact element against the workpiece
without pulling the trigger.
►Fig.21: 1.Contactelement2. Workpiece 3.Trigger
(not pulled)
— Insinglesequentialactuationmode,makesure
that the tool does not operate when pulling the
triggerrstandthenplacingthecontactelement
against the workpiece.
►Fig.22
Nailing method
Topreventthetriggerfrombeingaccidentallypulled,
the trigger lock lever is provided.
Tolockthetrigger,turnthetriggerlocklevertothelock
position
.
Tousethetool,turnthetriggerlocklevertotheunlock
position .
►Fig.23: 1.Triggerlocklever2.Trigger
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita AN935H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita AN935H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 17,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info