Manual Makita AN935H (page 9 of 84) (English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish)

657979

Zoom out

Zoom in

1/84

9 ENGLISH

6. Never point the tool toward yourself or anyone

whether it contains fasteners or not.

7. Do not rush the job or force the tool. Handle

the tool carefully.

8. Do not activate the tool unless the tool is

placed rmly against the workpiece.

9. Never hold or carry the tool with a nger on the

trigger or hand it to someone in this condition.

Accidentalringcancauseseriousinjury.

10. Never use fastener driving tools marked with

the symbol "Do not use on scaffoldings, lad-

ders" for specic application for example:

— when changing one driving location to

anotherinvolvestheuseofscaffoldings,

stairs,ladders,orladderalikeconstructions,

e.g.rooflaths;

— closing boxes or crates;

— ttingtransportationsafetysystemse.g.on

vehicles and wagons.

11. Check walls, ceilings, oors, roong and

the like carefully to avoid possible electrical

shock, gas leakage, explosions, etc. caused by

striking live wires, conduits or gas pipes.

12. Do not use the tool for fastening electrical

cables.Itisnotdesignedforelectriccableinstal-

lationandmaydamagetheinsulationofelectric

cablestherebycausingelectricshockorre

hazards.

13. Watch your footing and maintain your balance

with the tool. Make sure there is no one below

whenworkinginhighlocations,andsecuretheair

hosetopreventdangerifthereissuddenjerking

or catching.

14. On rooftops and other high locations, drive

fasteners as you move forward. It is easy to lose

yourfootingifyoudrivefastenerswhileinching

backward.Whendrivingfastenersagainstperpen-

dicularsurface,workfromthetoptothebottom.

Youcanperformdrivingoperationswithless

fatiguebydoingso.

15. A fastener will be bent or the tool can become

jammed if you mistakenly drive fastener on

top of another fastener or strike a knot in the

wood. The fastener may be thrown and hit

someone, or the tool itself can react danger-

ously. Place the fasteners with care.

16. Do not leave the loaded tool or the air com-

pressor under pressure for a long time out in

the sun. Be sure that dust, sand, chips and

foreign matter will not enter the tool in the

place where you leave it setting.

17. Never attempt to drive fasteners from both the

inside and outside at the same time. Fasteners

mayripthroughand/oryoff,presentingagrave

danger.

Service

1. Perform cleaning and maintenance right after

nishing the job. Keep the tool in tip-top condi-

tion. Lubricate moving parts to prevent rusting and

minimizefriction-relatedwear.Wipeoffalldust

fromtheparts.

2. Ask Makita authorized service center for peri-

odical inspection of the tool.

3. To maintain product SAFETY and RELIABILITY,

maintenance and repairs should be performed

by Makita Authorized Service Centers, always

using Makita replacement parts.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

PARTS DESCRIPTION

►Fig.2: 1.Trigger2.Triggerlocklever3. Hook

4. Magazine cap 5. Nose adapter (contact

element)

INSTALLATION

Selecting compressor

10 20 30 40 50 60

100

120

140

3 4

1.Nailingfrequency(times/min)2.Compressorair

outputperminute(L/min)3. 2.26 MPa (22.6 bar) 4. 1.77

MPa (17.7 bar) 5. 1.28 MPa (12.8 bar)

Theaircompressormustcomplywiththerequirements

ofEN60335-2-34.

Select a compressor that has ample pressure and air

outputtoassurecost-efcientoperation.Thegraph

showstherelationbetweennailingfrequency,applica-

ble pressure and compressor air output.

Thus,forexample,ifnailingtakesplaceatarateof

approximately40timesperminuteatacompressionof

1.77MPa(17.7bar),acompressorwithanairoutput

over100liters/minuteisrequired.

Pressure regulators must be used to limit air pressure to

theratedpressureofthetoolwhereairsupplypressure

exceeds the tool's rated pressure. Failure to do so may

resultinseriousinjurytotooloperatororpersonsinthe

vicinity.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita AN935H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 17,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita AN935H Manual

Product: