Manual Liebherr SWTNes 4285 (page 18 of 32) (English)

716906

Zoom out

Zoom in

1/32

NOTICE

Damaged solenoid thread pitch.

The solenoid leaks: Water may leak out.

uPosition the nut Fig. 46 (1) carefully and screw it directly

onto the thread with two fingers until it is seated

securely.

uTighten the nut Fig. 46 (1)clockwise with the auxiliary

tool Fig. 45 (5) until maximum torque is reached and the

auxiliary tool Fig. 45 (5) overtightens.

Connecting the hose to the stopcock:

uScrew the nut Fig. 45 (7) onto the stopcock Fig. 45 (8).

uTighten the nut Fig. 45 (7)clockwise with the auxiliary

tool Fig. 45 (5) until maximum torque is reached and the

auxiliary tool Fig. 45 (5) overtightens.

uTurn the water supply stopcock Fig. 45 (8) on and check

the whole water system for leaks.

uFlushing the IceMaker: Turning the IceMaker on chapter

(see 5.4.10.2 Switch the IceMaker on.) .

uHook the clip Fig. 45 (6) into the auxiliary tool Fig. 45 (5)

and fix it to the stainless steel pipe to store it.

4.5 Sliding into the row of units

Fig. 47

A [mm] B [mm] C [cm2]D [mm] E [mm]

665 x65 min. 300 min. 50 min. 46

x If using wall spacers, add 15 mm (see 4.2 Installing the

appliance) .

These dimensions apply to an opening angle of 90°. Clear‐

ances vary depending on the opening angle.

Please contact Customer Services to purchase a kit to

limit the door opening angle to 90° for appliances with soft-

closing devices.

The appliance can be built into kitchen units. A top

cupboard Fig. 47 (2) can be added above the appliance in

order to bring the appliance Fig. 47 (1) up to the height of the

fitted kitchen units.

The appliance can be installed right next to the kitchen

cabinet Fig. 47 (3). The appliance must protrude by depth

Fig. 47 (B) from the front of the cabinet so that the

doors can be opened fully. The appliance may protrude

further depending on the depth of the kitchen cabinets and

whether wall spacers are used.

NOTICE

Danger of overheating due to insufficient air ventilation!

The compressor may be damaged if there is insufficient air

ventilation.

uTake care to ensure adequate air ventilation.

uObserve the ventilation requirements.

Ventilation requirements:

-There are spacer fins at the back of the appliance to

provide adequate ventilation. Make sure these do not end

up in recesses or openings.

-At the back of the top cabinet, there must be an air outlet

shaft with depth Fig. 47 (D), spanning the entire width.

-The ventilation shaft Fig. 47 (C) must be observed under

the ceiling.

-The wider the ventilation clearance, the more efficiently

the appliance will run.

If the appliance is installed with the hinges next to a wall

Fig. 47 (4), the distance Fig. 47 (E) between the appliance

and the wall must be observed. This is how far the handle

protrudes when the door is open.

4.6 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic

film!

uDo not allow children to play with packing material.

The packaging is made of recyclable materials:

-corrugated board/cardboard

-expanded polystyrene parts

-polythene bags and sheets

-polypropylene straps

-nailed wooden frame with polyethylene panel*

uTake the packaging material to an official collecting

point.

4.7 Connecting the appliance

WARNING

Failure to connect properly

Fire hazard.

uDo not use an extension cable.

uDo not use distributor blocks.

NOTICE

Failure to connect properly

Damage to the electronics.

uDo not connect the appliance to a stand-alone inverter,

e.g. solar power systems and petrol generators.

uDo not use an energy saving plug.

Note

Only use the power connection lead supplied.

uA longer power connection lead can be ordered from

Customer Service.

Putting into operation

18 * Depending on model and options

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr SWTNes 4285 in the language / languages: English as an attachment in your email.

The manual is 2.28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr SWTNes 4285

Liebherr SWTNes 4285 User Manual - German - 34 pages

Liebherr SWTNes 4285 User Manual - Dutch - 34 pages

Liebherr SWTNes 4285 User Manual - French - 34 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr SWTNes 4285 Manual

Product: