716906

Liebherr SWTNes 4285 Manual

15
Zoom out
Zoom in
Previous page
1/32
Next page
uCarefully lift up the plugs with a slotted screwdriver and
remove them. Fig. 35 (1)
uPosition the door from above onto the lower bearing pins.
Fig. 35 (2)
uInsert the centre bearing pin through the centre bearing
bracket into the lower door. Make sure that the catch
mechanism is pointing to the rear. Fig. 35 (3)
uInsert the plugs again on the other side of the door.
Fig. 35 (4)
4.3.12 Fitting the upper door
Fig. 36
uPlace the upper door on the centre bearing pins Fig. 36 (1)
uAlign the top of the door with opening in the bearing
bracket. Fig. 36 (2)
uInsert the bolt and tighten with a T15 screwdriver.
Fig. 36 (3)
uFit the protective cover to protect the door: Insert the
protective cover and check that it is attached to the door.
If not, insert the bolt fully. Fig. 36 (4)
NOTICE
Cable crushing
uThe mark on the cable must be centred in the holder. The
tab with the longer opening must point forwards.
uInsert the holder with its cable into the opening.
Fig. 36 (5)
uPress the holder downwards until the tab clicks into
place. Fig. 36 (6)
uInsert the plugs. Fig. 36 (7)
4.3.13 Fitting the cable connection
Fig. 37
uEngage the plug above the upper bearing bracket and
carefully place the cable strands into the channel.
Fig. 37 (1)
uCarefully position the grey cable in the guide above the
top bearing bracket. Fig. 37 (2)
Fig. 38
uInsert the grey cable into the guide in the top door.
Fig. 38 (1)
uEngage the plug. Fig. 38 (2)
uPosition the remaining cable length as a loop in the
guide, if required.
4.3.14 Aligning the doors
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly
enough, the door may drop out. This may lead to severe
injuries. What is more, the door may not close and therefore
the appliance may fail to cool properly.
uScrew the turn hinges firmly into place with 4 Nm.
uCheck all of the screws and retighten if necessary.
uAlign the doors flush with the appliance housing using
the two oblong holes in the lower bearing bracket and
centre bearing bracket if needed. To do this undo the
middle screw in the bottom bearing bracket with the T25
tool supplied. Undo the remaining screws a little with
the T25 tool or with a T25 screwdriver and align using
the slotted holes. Undo the screws in the middle bearing
bracket with the T25 tool and align the middle bearing
bracket using the slotted holes.
Putting into operation
* Depending on model and options 15
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr SWTNes 4285 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr SWTNes 4285 in the language / languages: English as an attachment in your email.

The manual is 2.28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr SWTNes 4285

Liebherr SWTNes 4285 User Manual - German - 34 pages

Liebherr SWTNes 4285 User Manual - Dutch - 34 pages

Liebherr SWTNes 4285 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info