693399

Ksenia Lares 4.0 Manual

31
Zoom out
Zoom in
Previous page
1/58
Next page
lares 4.0 PROGRAMMING MANUAL
31
rev. 0/2018
Custom Balancing
In this section, custom configurations can be created for the end-of-line resistors to be associated then with the zones.
It is possible to modify the intervention thresholds and possibly the behaviour of the input (short, resting, alarm, masking/
fault, tamper), starting from the basic configuration of the standard balancing.
In this page, next to the session management buttons, the following button appears: (
)
By clicking on this option, you can open an Excel spreadsheet that allows to easily determine the thresholds to be applied
according to the end-of-line resistors installed.
Control through the APP
• Not visible: if this option is selected, the output will not be displayed in the APP and Web server in the page of
real-time output.
• With PIN (local) - With PIN (remote): in this case, the output will be managed locally with PIN and it will be managed
through the APP in the same way.
• With PIN (local) - Not managed (remote): in this case, the output will be managed locally by PIN but it will not be
possible to manage it through the APP (even if displayed).
• Without PIN (local) - Without PIN (remote): in this case, the output will be managed locally without PIN and it will be
managed through the APP in the same way.
• Without PIN (local) - Not managed (remote): in this case, the output will be managed locally without PIN but it will
not be possible to manage it through the APP (even if displayed).
• Without PIN (local) - With PIN (remote): in this case the output will be managed locally without PIN but it will be
required to enter a code to manage it through the APP.
Polarity
• Normally open: select this option if you want an O.C. (open collector) output in resting state to be open and closes to
the ground when it is activated (negative to give) or if you want the relay contact (e.g. relay auxi) to be open.
• Normally closed: select this option if you want an O.C. output in the resting state to be closed to ground and opens
when it is activated (negative to miss) or if you want the relay contact (e.g. auxi relay) to be closed.
ON time (sec)
Time in seconds, for which an output programmed as monostable remains active when
an event occurs.
Note: this option only appears if you set a monostable output.
Cycle time (sec)
It is the sum of the ON time and minimum time for which the output is required to be deactivated.
• Activate only if the system is armed: the output is activated only if the partition (or partitions) associated with it is
armed.
N.B.: This option is available only if you set the "tamper" or "alarm and tamper" mode
… 31 …


Need help? Post your question in this forum.

Forumrules
1

Forum

ksenia-lares-4.0

Reset search

  • Hi
    We have a message peripherals lost. What does this mean? Submitted on 24-7-2021 at 08:15

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ksenia Lares 4.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ksenia Lares 4.0 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info