Manual Ksenia Lares 4.0 (page 33 of 58) (English)

693399

Zoom out

Zoom in

1/58

lares 4.0 PROGRAMMING MANUAL

rev. 0/2018

Processing mode

After having associated the zone with the device, the type of analysis of the signal required to generate an alarm is

determined.

Note: some modes may not be usable depending on the type of device selected (e.g. on the lares 4.0 board, only the

standard and command modes will be available)! For convenience, all available conﬁgurations will be shown.

There are four modes:

1. Standard: to be combined with contacts, detectors, etc.

Note: not available for unum WLS, velum WLS, nebula WLS, auxi WLS.

2. Command: this zone does not generate alarms, but is only used to activate scenarios.

To program a command zone, associate the partitions to be armed/disarmed with the zone.

Subsequently, in the "Events" page, associate the real-time zone (alarm) with the scenario to be activated.

If all the partitions managed by that scenario are not associated, only the selected partitions will be armed/disarmed.

If this option is activated, it is possible to directly manage an output (or a group of outputs using a Hashtag) without

creating a scenario. In this case, the following additional conﬁgurations are displayed:

a. Command output: in this menu, it is possible to select the output (or the group of outputs via Hashtag) that you

want to be managed by the command zone

b. Type of activation: in this menu, it is possible to select the type of action to be performed on the output: activation,

deactivation, switching (with respect to the current status)

c. Command mode: in this menu, it is possible to select the type of command between the button (the action on the

output will be carried out only when the zone is opened) and switch (the action is performed both at the opening

and closure of the zone)

N.B.: This feature is not available for unum WLS, velum WLS, nebula WLS, auxi WLS.

3. Inertial/Glass break: to be combined with seismic, glass break detectors etc.

Not available for lares, ergo-rev.0, duo, unum WLS, nanus WLS, velum WLS, nebula WLS, auxi WLS.

4. Shutter: to be combined with detectors for shutters (e.g. contact ropes etc.)

Not available for lares, ergo-rev.0, duo, unum WLS, nanus WLS, velum WLS, nebula WLS, auxi WLS.

• Test: If this option is selected, only events in the event log will be traced without generating an alarm.

• Input delay: Select this option if you want the violation of the zone to trigger the initiation of the input time (or if this

time has already been started, ensure that the alarm is not triggered). It is possible to establish an entrance path on

multiple levels by programming the input level parameter. For example, when partitions are armed, if you program

three levels, you have the following behaviour:

1) at active warning time: it is possible to breach only the zones one level higher than the last breached zone.

2) at inactive warning time: it is possible to breach only the zones of level 1; the warning time starts at the ﬁrst

breach.

The ﬁgure shows a hypothetical situation of entrance into a house where the control panel of the system can be reached

only after having intercepted some areas.

Speciﬁcally, the volumetric sensor marked with ( 1 ) must be the ﬁrst to be violated so as not to generate an alarm. Then,

the number (2) and the number (3) will follow.

Attention: for correct functioning, the zones that intervene in the entrance path must have at least

one partition in common.

Hi
We have a message peripherals lost. What does this mean? Submitted on 24-7-2021 at 08:15
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ksenia Lares 4.0 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ksenia Lares 4.0 Manual

Product: