693399
26
Zoom out
Zoom in
Previous page
1/58
Next page
rev. 0/2018
lares 4.0 PROGRAMMING MANUAL
26
Wireless repeaters
duo (with external power supply and buffer battery).
The parameters available for duo repeaters are:
• Description: the name given to the device (e.g. first-floor repeater etc.)
• Serial number: this is the code which identifies the peripheral. Simply update the serial number to acquire the new
peripheral and to keep any previously saved settings if the device is being replaced.
Wireless I/O modules:
auxi wls
The parameters available for WLS auxi are:
• Description: the name given to the device (e.g. turning on the outdoor lights etc.)
• Serial number: six-digit code that identifies the device. Simply update the serial number to acquire the new peripheral
and to keep any previously saved settings if the device is being replaced.
• Type of outputs: the outputs can be programmed to operate in one of the following modes:
• Independent: the outputs associated with the device are completely independent.
• Switch: the two outputs on the device are treated as a single logic output.
The first one is normally open and the second one is normally closed.
This operating mode uses only one control panel output.
• Interlocked: in this mode, which is particularly useful for controlling the electric motors, the outputs
cannot be concomitantly active.
If the activation of an output is commanded while the other is active, the switching will be preceded
by the deactivation of both outputs for half a second.
Wireless sensors:
nanus poli
The parameters available for the nanus wireless magnetic contacts are:
• Description: the name given to the device (e.g. kitchen windows contact etc.).
• Serial number: this is the code which identifies the peripheral. Simply update the serial number to acquire the new
peripheral and to keep any previously saved settings if the device is being replaced.
• Supervision: maximum time between two consecutive transmissions.
poli
The parameters available for the poli wireless magnetic contacts are:
• Description: the name given to the device (e.g. entrance door contact etc.).
• Serial number: six-digit code that identifies the device. Simply update the serial number to acquire the new peripheral
and to keep any previously saved settings if the device is being replaced.
• Supervision: maximum time between two consecutive transmissions.
unum
The parameters available for the unum wireless detectors are:
• Description: the name given to the device (e.g. living room sensor etc.).
• Serial number: this is the code which identifies the peripheral. Simply update the serial number to acquire the new
peripheral and to keep any previously saved settings if the device is being replaced.
• Supervision: maximum time between two consecutive transmissions.
• Inhibition: this is the time (expressed in seconds) between the transmission of two alarms. To save the battery power,
the detector emits only one alarm during the set interval even if the events that generate the alarms are multiple.
Minimum configurable time: 5 seconds.
Maximum configurable time: 300 seconds.
26


Need help? Post your question in this forum.

Forumrules
1

Forum

ksenia-lares-4.0

Reset search

  • Hi
    We have a message peripherals lost. What does this mean? Submitted on 24-7-2021 at 08:15

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ksenia Lares 4.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ksenia Lares 4.0 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info