690032
26
Zoom out
Zoom in
Previous page
1/194
Next page
For drinks with frothy milk or hot water, the drip tray has been specially designed to allow you to fit a large
cup under the steam nozzle or the super cappuccino accessory, once the magnetised box has been
removed. The cup is ideally positioned to collect the frothy milk or the hot water produced by the nozzle
or the super cappuccino accessory. Furthermore, you can use the box as storage for the super cappuccino
accessory.
5.1 Making drinks with hot water
Make sure that the steam nozzle is securely fitted on its tip.
While the screen displays the drink selection menu, press the “hot water” key . Fig. 14.
A message will invite you to place a container under the steam nozzle. Again press the “hot water” key
to produce hot water.
To interrupt the steam function, just press any key.
If the nozzle is blocked, clean it out with a fine needle.
Steam froths up the milk to make a cappuccino or a caffe latte, for example, and also heats up
liquids. As you need a higher temperature to produce steam than to make an espresso, the
appliance runs an additional pre-heating phase for steam.
While the screen displays the drink selection menu, press the “steam” key . Fig. 15.
A screen will inform you that the appliance is being pre-heated. Once the pre-heating phase has been
completed, a message will ask you to place a container under the steam nozzle. Press the “steam” key
again to start generating steam. A little water will be produced first and then steam will start. Use the same
key to stop steam generation.
Be careful, because the cycle does not stop immediately.
Note: We recommend that you use very cold, fresh pasteurised or UHT milk that has been recently
opened. Do not use untreated milk.
6.1 Super Cappuccino Accessory (depending on model)
The super cappuccino accessory helps the preparation of a cappuccino or latte.
Attach the various parts together. Fig. 16
Put the beveled end to the milk.
Select the cappuccino or caffe latte position on the special nozzle. Fig. 17
Fill up the milk pot and place a cup or a glass underneath the Super-cappuccino nozzle.
Fig. 18-19
Press the button to start and then to stop the cycle.
Place your cup under the coffee outlets and start a coffee / espresso cycle. Fig. 20
Important: The inlet must not be twisted.
Cleaning and maintenance: remove the accessory and clean the parts using a small brush and, if necessary,
a little washing-up liquid. Make sure to carefully clean the parts circled in the photo. The hole in the metal
part should not be allowed to become blocked. Fig. 21.
To prevent milk from drying on the auto-cappuccino accessory, it must be cleaned thoroughly after use..
It is recommend that you wash it immediately by carrying out a cycle with steam and the accessory pot
filled with water in order to clean the inside of the nozzle. To do so, you can also use liquid cleaner, available
as an accessory.
5. PREPARING OTHER DRINKS
6. MAKING DRINKS WITH THE SUPER CAPPUCCINO
ACCESSORY OR THE STEAM NOZZLE (depending on model)
!
!
28
KR_ESPRESSO_EA83_EO_EA83_NEW CHARTE 30/05/13 11:35 Page28
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Krups EA83 serie at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Krups EA83 serie in the language / languages: All languages as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info