668721
28
Zoom out
Zoom in
Previous page
1/94
Next page
22
Editing the arpeggiator
The R3’s arpeggiator provides six arpeggio types. In addition to selecting
an arpeggiator type, you can adjust the duration (gate time) , note value,
swing amount, tempo, and other arpeggiator parameters. These arpeg-
giator settings are adjusted using the 32. Arpeggiator-A page and 33.
Arpeggiator-B page parameters. Arpeggiator patterns can be up to eight
steps long, and each step can be individually switched on or off (play or
mute), providing more rhythmic versatility. (Refer to page 15 for more
information about arpeggiator steps.)
Selecting which timbre(s) will be played by the arpeggiator
In a synth program that uses two timbres, you can select which timbre(s)
will be played by the arpeggiator. This is specified by Arpeg-A page
“Assign” (knob [1]). You can arpeggiate both timbres, only timbre 1 or
only timbre 2.
Sync’ing the LFO rate and the delay time to the arpeggiator
By synchronizing the LFO 1/2 rate to the tempo of the arpeggio, you can
apply modulation that follows the arpeggiator tempo. You can also set
the time parameter of the delay effect to be a ratio of the tempo, so that
the delay time will remain appropriate even if you change the tempo of
the arpeggio. This is particularly convenient for live performances.
Because the R3’s arpeggiator can be synchronized to an external MIDI
sequencer, then in turn you can control the LFO 1/2 rate or the delay
time from an external MIDI sequencer. (p.67)
Basic editing
How to read the pages for each section
Knob [2]
Reso1 (Filter1 Resonance) [0...127]
Sets the resonance of the filter. This will
emphasize the overtones near the cutoff
frequency specified by “Cutoff1,” adding
a distinctive character to the sound. In-
creasing this value will increase the effect.
Since movement of the “Cutoff1” knob will
affect the overtones that are boosted by
resonance, it is best to adjust “Cutoff1” and
“Reso1” in conjunction with each other
(Figure 8-1).
Depending on the cutoff frequency or
the input audio, increasing this value
may cause distortion.
Knob [3]
Filt1Bal (Filter1 Balance)
[LPF24…LPF12…HPF…BPF…THRU]
Selects the filter type. Intermediate settings
will produce a response that is between the
two filter types.
LPF12 (–12dB/oct), LPF24 (–24dB/oct):
Low Pass Filter (p35 “LFP:”).
HPF (-12dB/oct): High Pass Filter (p35
“HFP:”).
BPF (-12dB/oct): Band Pass Filter (p35
“BFP:”).
THRU: The sound will output directly,
without passing through the filter.
Knob [1]
Cutoff1 (Filter1 Cutoff) [0...127]
Sets the cutoff frequency.
Increasing this value will raise the cutoff
frequency.
“Cutoff1” can be varied by time-vari-
ant change produced by EG1, by key-
board playing dynamics (velocity),
and by note location (keyboard track-
ing).
If the “Cutoff1” value is set too low,
the volume may be extremely low, or
you may hear no sound at all.
8. FILTER1-A
The filter section changes the tonal character of the oscillators by passing only the desired portion of the sound - either above (Low Pass),
below (High-Pass), or centered on (Band Pass) the cutoff frequency. The R3 has two filters (filter 1 and filter 2), and you can change their
routing to create more complex filter sounds. The filter 1 parameters are set in the 8. FILTER1-A page and 9. FILTER1-B page.
Knob [4]
Routing1 [Single, Serial, Para, Indiv]
Specifies the routing (connection) between
filter 1 and filter 2.
Single: Only filter 1 is used.
Serial: Filter 1 and filter 2 are connected in
series (Figure 8-2).
Parallel: Filter 1 and filter 2 are connected
in parallel (Figure 8-3).
Indiv: Filter 1 is applied to oscillator 1, and
filter 2 is applied to oscillator 2 and noise
(Figure 8-4).
These are the edit control
knobs [1]–[4]. The markings
printed around each knob are
the values that will be selected
when you turn that knob.
These positions are
approximate.
This area lists the parameters
that are edited by edit control
knobs [1][4] when the above
section is selected. The range of
values for each parameter is
given in square brackets [ ].
Explanations of each parameter
and its values are given below.
This is the name of the section.
When you have set the [PAGE]
dial to the 8. Filter1-A page and
would like to see an explanation of
the parameters, refer to this page.
A summary of this section is
given here.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Korg R3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Korg R3 in the language / languages: English as an attachment in your email.

The manual is 5,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info