Manual Konig Electronic SEC-ALARM210 (page 7 of 151) (English, German, Dutch, French, Italian, Swedish, Spanish, Finnish)

508772

Zoom out

Zoom in

1/151

Step 6:

A walk test should be performed after the motion detection

sensor has been mounted. Walk in the detected area, if motion

is detected, a red light inside the sensor will light up. If the red

light does not light up, motion has not been detected and you

may need to re-position the sensor. Ensure you test all the

locations that you would like the motion detection sensor to

cover.

Detecting area in meters

Note:

- Perform the walk test after the battery has

been inserted for more than one minute.

- Before performing the walk test, the motion

detection sensor should not detect any

motion.

- After motion is detected once, the motion

detection sensor will not be triggered

unless no motion is detected for

20 seconds. Wait for at least 20 seconds

during walk testing between 2 activations.

The motion detection sensor only detects

the first motion and again after 20 seconds.

If you experience false triggering, please pay attention to the following.

- When installing the motion sensor, avoid placing it near heating or cooling devices. Air movement,

especially those caused by changes in temperature, may trigger the motion detection sensor and

cause false alarms. Please carefully test your motion detection sensor so that it will only be

triggered by wanted movement.

- There is a jumper for sensitivity setting. You may change the sensitivity to low if you experience

false triggering. You will find the jumper setting on the left side of the test button. You can place the

small black plastic part on the pins with position 1 or 2. Position 1 is high sensitivity and position 2

is low sensitivity.

System status, sensor failure and low battery indication:

The control centre constantly monitors its sensors. If the control centre fails to communicate with any

sensors, the zone indicator will start flashing rapidly.

When sensor failure occurs, try the following:

1. Check if the sensor is located where it should be, and whether there is any physical damage to the

sensor.

2. If the failed sensor is not physically damaged, try to activate the sensor and see if the control

centre reacts to such activation.

3. If not, try to remove the sensor from its location, and bring it closer to the control centre and

activate the sensor. It is possible that the sensor is installed too far from the control centre and it

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic SEC-ALARM210 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 2,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Konig Electronic SEC-ALARM210 Manual

Product: