683161
170
Zoom out
Zoom in
Previous page
1/196
Next page
Control of External Devices
TX Inhibit in Busy State (when Squelch is Open)
When transmission is inhibited in the busy state, pressing [SEND]
on the front panel or [PTT] on the microphone does not execute
transmission while this transceiver is busy.
Configure in Advanced Menu [12] TX Inhibit While
Busy
Setting Value Off (default)/ On
Reversing the PKS Signal Polarity
Short-circuiting the PKS terminal to GND places this transceiver
in the TX mode. This polarity can be reversed according to the
device to be connected.
Configure in Advanced Menu [11] PKS Polarity
Reverse
Setting Value Off (default)/ On
Off: Short-circuiting the PKS terminal of the ACC 2 connector
to GND places this transceiver in the TX mode.
On: Applying a voltage of 3 V to 5 V to the PKS terminal of the
ACC 2 connector places this transceiver in the TX mode.
USB Keying
This function is compatible with PC applications for controlling the
different behaviors including CW keying, RTTY frequency shift and
PTT/SEND (TX/RX switching) using the RTS/DTR signal of the
COM port.
It allows the above behaviors to be assigned to the RTS and DTR
signals of the 2 virtual COM ports (Standard and Enhanced) during
USB connection.
Off: Disabled
Flow Control: Behaves as a hardware flow control signal for
command communication.
CW Keying: Behaves as a CW keying signal.
RTTY Keying: Behaves as an RTTY frequency shift key signal.
PTT: Behaves in the same way as PTT (SEND).
DATA SEND: Behaves in the same way as DATA SEND (PKS).
Configure in Advanced Menu [17]
Virtual Standard
COM Port – RTS
Setting Value
Flow Control (default)/ CW Keying/ RTTY
Keying/ PTT/ DATA SEND
Configure in Advanced Menu [18] Virtual Standard
COM Port – DTR, [19] Virtual Enhanced COM Port
– RTS or [20] Virtual Enhanced COM Port – DTR
Setting Value
Off (default)/ CW Keying/ RTTY Keying/ PTT/
DATA SEND
To switch the COM port or exit the application in the PC
application for performing transmission on the
transceiver using the USB keying function, be sure to
complete the transmission before doing so. Otherwise
transmission error may occur on the transceiver.
If the COM port for outputting the USB keying signal is
not selected (open) in the PC application that is using the
USB keying function, the signal for USB keying may be
accidentally transmitted. Press [
] to turn off the power
of this transceiver or disable the USB keying function
temporarily until the preparation on the PC application is
completed.
“RTTY Keying” can only be configured for 1 out of the 4
signals (duplicate configuration is not allowed).
When this menu is configured to “RTTY Keying” (during
RTTY operation via USB keying), RTK of the ACC 2
connector will be disabled.
Please use the latest virtual COM port driver.
Decoded Character Output
This function outputs characters decoded by the built-in decoder
of CW/ RTTY/ PSK from the virtual COM port (Enhanced). The
baud rate is also variable.
Turning ON/OFF Decoded Character Output
Configure in Menu [7-03]
Decoded Character
Output
Setting Value Off (default)/ On
Configuring the Baud Rate of the Virtual COM
(Enhanced) Connector
Configure in Menu [7-02]
Baud Rate (Virtual
Enhanced COM)
Setting Value
9600/ 19200/ 38400/ 57600/ 115200 (default)
[bps]
16 OTHER FUNCTIONS
16-12
170


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info