683161

Kenwood TS-890S Manual

168
Zoom out
Zoom in
Previous page
1/196
Next page
Operation
1 Transfer the TX frequency and mode information
during split operation from the TX/RX end to the
sub-receiver end.
By pressing [SPLIT] at the TX/RX end to switch to the split
mode, the TX frequency and mode information is transferred
to the VFO of the sub-receiver and enables the TX frequency
to be received by the sub-receiver.
Subsequently, when there is a change in the TX frequency at
the TX/RX end, the new TX frequency information will be
transferred automatically, and the RX frequency at the sub-
receiver will be adjusted accordingly. Below are some
examples.
•
When the TX frequency is changed using the XIT function
•
When the RX band and TX band are changed at the same
time using the Band Direct key (“RX/ TX Band” needs to be
selected in advance in Menu [3-13] “Band Direct Keys in
Split Mode”.)
•
When the split TX frequency is changed via operation of the
[RIT/XIT] control (“TX Frequency Offset while RX” needs to
be selected in advance in Menu [3-12] “Split Frequency
Offset by RIT/XIT Control”.)
2 Change the RX frequency and mode that are
transferred from the TX/RX end at the sub-receiver
end.
The frequency and mode that are transferred to the sub-
receiver end can be adjusted independently without affecting
the value at the TX/RX end.
To restore the state where the frequency matches with the TX
frequency at the TX/RX end, press [SPLIT] at the TX/RX end
to reactivate the split function.
3 Transfer the frequency detected at the sub-receiver
end to the TX frequency at the TX/RX end.
Pressing [<Q-M.IN] at the sub-receiver end transfers the
current frequency and mode information to the TX VFO at the
TX/RX end.
●
Upon transmission from the TX/RX end, the sub-receiver
switches to the standby mode.
●
The transceiver at the sub-receiver end is inhibited from
transmission.
●
When XIT at the TX/RX end is ON, the XIT frequency is
added to the frequency to be transferred.
●
When RIT at the sub-receiver end is ON, the RIT
frequency is added to the frequency to be transferred.
●
The transceiver at the TX/RX end is unable to receive
the frequency and mode information from the sub-
receiver if it is not configured to the split mode.
●
The transceiver at the TX/RX end is able to receive the
frequency and mode information from the sub-receiver
even when it is in the frequency lock mode.
Muting the Sub-receiver
The RX audio at the sub-receiver can be muted by the TX/RX end.
1 Assign “Mute (Sub Receiver)” to a PF key at the TX/
RX end.
2 Press PF [Mute (Sub Receiver)].
The RX audio at the sub-receiver end is muted.
•
Pressing the PF [Mute (Sub Receiver)] key again unmutes
the RX audio.
Split Transfer B
This function supports the “split transfer” function on models
before the TS-890S. It allows existing users of the “split transfer”
function to continue using it after changing to TS-890S.
Follow the steps below to operate this transceiver. To combine the
use of a transceiver other than this transceiver, please refer to the
instruction manual of the model to be used.
Using TS-890S at the Sub-receiver End (Master)
1 Turn ON Split Transfer B.
Select “B” in Menu [7-04] “Quick Data Transfer”.
2 Tune to the frequency of the party to communicate
with in the VFO mode.
Operate the Tuning control to tune to the frequency of the party
to communicate with.
3 Transfer the frequency and mode information to the
TX/RX end.
Pressing [<Q-M.IN] saves the frequency and mode information
to channel 0 of the quick memory and transfers it to quick
memory channel 0 or VFO at the TX/RX end.
Using TS-890S at the TX/RX End (Slave)
1 Turn ON Split Transfer B.
Select “B” in Menu [7-04] “Quick Data Transfer”.
2 Configure whether frequency and mode
information transferred from the sub-receiver is to
be received by the quick memory channel or VFO.
Select “VFO” or “Quick Memory” in Menu [7-05] “Overwrite
Location (Quick Data Transfer)”.
3 Receive frequency and mode information from the
sub-receiver.
Upon receiving frequency and mode information that are
transferred from the sub-receiver, channel 0 of the quick
memory or VFO is updated according to the setting in step 2.
●
Configure the 2 transceivers that are connected to each
other to the same COM connector baud rate.
●
To prevent malfunction, reboot both transceivers after
configuring the settings.
●
When using this transceiver as a sub-receiver, configure
Menu [6-03] “TX Inhibit” to “On” to prevent erroneous
transmission.
●
The transceiver at the TX/RX end is able to receive the
frequency and mode information from the sub-receiver
even when it is in the frequency lock mode.
16 OTHER FUNCTIONS
16-10
… 168 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info