683161
167
Zoom out
Zoom in
Previous page
1/196
Next page
Split Transfer
This function allows frequency information to be transferred by
connecting another transceiver to this transceiver as a sub-
receiver. There are two modes for this function: Split Transfer A
and Split Transfer B.
Split Transfer A
This function transfers information on the TX VFO frequency and
mode during split operation from the transceiver (TX/RX end) to
the transceiver that functions as a sub-receiver. This is a
convenient function for simultaneous dual-frequency reception by
having the sub-receiver receive the split frequencies from the TX/
RX end. The sub-receiver also supports the standby function.
.
Simultaneous Reception of TX Frequency
Split Operation
Sub-receiverTX/RX End
The usable transceiver models are TS-890S, TS-590SG and
TS-590S. TS-590S can be used only as a sub-receiver.
Firmware update is needed when TS-590S/ TS-590G is
used as a sub-receiver.
The TS-590G series can also be used as a transceiver
at the TX/RX end for Split Transfer A. Firmware update
is necessary regardless of whether it is used as a sub-
receiver or a transceiver at the TX/RX end.
Some functions may not be usable during split transfer
between the TS-890 series and another transceiver due
to differences in the specifications.
Split Transfer B
This mode is used for connecting another transceiver to this
transceiver as a sub-receiver during two-man operation while
contesting. This is a convenient function that allows the sub-
operator at the sub-receiver end to transfer frequency and mode
information to the main operator at the TX/RX end.
Operating data can be transferred by the following transceiver
models.
TS-890S
TS-990S
TS-590S
TS-590SG
TS-480 series
TS-2000 series
TS-570 series
TS-870S
Some functions may not be usable during split transfer
between this transceiver and another transceiver.
Connection
Connect the 2 transceivers to enable transfer of frequency data
and sharing of antenna.
Cables for connection need to be prepared separately
by the user.
Connection for Data Transfer:
Connect the COM connector of the 2 transceiver units using a
RS-232C cross cable (female-female).
.
Compatible TransceiverTS-890S
(Female)
RS-232C Cross Cable
(Female)
Connection for Antenna Sharing:
Connect the ANT OUT connector at the TX/RX end to the ANT or
RX IN connector at the sub-receiver end using a coaxial cable.
Turn on the ANT OUT function at the TX/RX end. Select the
connected ANT connector at the sub-receiver end or make use of
the RX ANT function.
Split Transfer A
Below is an example of using this transceiver at both the TX/RX
end and sub-receiver end in the standard settings. Before using
the TS-590SG/ TS-590S as a sub-receiver, please read through
the instruction manual and update documents.
Configuration
Using TS-890S at the TX/RX End
1 Enable this transceiver to function as a TX/RX end
transceiver.
Select “A (TX/RX)” in Menu [7-04] Quick Data Transfer.
2 Configure the baud rate to 115200 bps.
Select “115200 [bps]” in Menu [7-00] Baud Rate (COM Port).
3 Set to the VFO mode.
If the transceiver is in the memory channel or quick memory
channel mode, switch it to the VFO mode.
Using TS-890S as a Sub-receiver
1 Enable this transceiver to function as a sub-
receiver.
Select “A (Sub RX)” in Menu [7-04] Quick Data Transfer.
2 Configure the baud rate to 115200 bps.
Select “115200 [bps]” in Menu [7-00] Baud Rate (COM Port).
3 Set to the VFO mode.
If the transceiver is in the memory channel or quick memory
channel mode, switch it to the VFO mode.
4 Set to simplex mode.
This transceiver functions only at the transfer rate of
115200 [bps].
It does not function in the memory channel and quick
memory channel modes.
This function cannot be used in the split mode.
OTHER FUNCTIONS 16
16-9
167


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info