683161
165
Zoom out
Zoom in
Previous page
1/196
Next page
External Monitor Output
Connecting an external monitor to the DISPLAY connector
enables the image displayed on the screen of this transceiver to
be displayed on the external monitor at the same time.
Configure in Advanced Menu [21] External
Display
Setting Value Off/ On (default)
Configuring the External Monitor Resolution
The resolution of the external monitor that is connected to the
DISPLAY connector can be configured.
Configure in Advanced Menu [22] Resolution
(External Display)
Setting Value 800 x 600 (default)/ 848 x 480
When the resolution of the external monitor is changed,
a resolution switch screen will appear for approximately
5 seconds before the change is applied.
Configuring Audio Input/Output
Configuring the USB Connector Input/Output Signal
The input/output level of the audio signal when an external device
is connected to the (USB-B) connector on the rear panel can be
configured.
Configuring the Audio Signal Input Level
Configure the audio input level for the (USB-B) connector on the
rear panel.
Configure in Menu [7-06]
USB: Audio Input Level
Setting Value 0 to 50 (default) to 100 (1 step)
Configuring the Audio Signal Output Level
Configure the audio output level for the (USB-B) connector on the
rear panel.
Configure in Menu [7-08]
USB: Audio Output
Level
Setting Value 0 to 100 (default) (1 step)
When using a Windows PC, wait for the PC to recognize
this transceiver, then select Control Panel → Hardware
and Sound → Sound → Recording → Microphone (USB
Audio CODEC) → Properties, followed by selecting “2
channel”.
Windows is a registered trademark of Microsoft
Corporation in the United States and other countries.
Configuring the ACC 2 Connector Input/Output
Signal
The input/output level of the audio signal when an external device
is connected to the ACC 2 connector on the rear panel can be
configured.
Configuring the Audio Signal Input Level
Configure the level of audio signal input to the ACC 2 connector
on the rear panel.
Configure in Menu [7-07] ACC 2: Audio Input
Level
Setting Value 0 to 50 (default) to 100 (1 step)
Configuring the Audio Signal Output Level
Configure the input/output level of the audio signal when an
external device is connected to the ACC 2 connector on the rear
panel.
Configure in Menu [7-09] ACC 2: Audio Output
Level
Setting Value 0 to 50 (default) to 100 (1 step)
Configuring the TX Monitor Level for External Audio
Output
Configure the level of the TX monitor audio that is output from the
rear connector.
Configure in Menu [7-10]
TX Monitor Level (Rear
Connectors)
Setting Value Linked (default)/ 0 to 20 (1 step)
Configuring to “Linked” changes the level in tandem with the
level configured during TX monitor level adjustment.
Configuring Audio Mixing for the External Audio
Output Connector
Configure whether to mix the audio produced by this transceiver
with the RX audio that is output from the (USB-B) connector and
ANO terminal of the ACC 2 connector.
Configure in Menu [7-11]
Audio Output Type (Rear
Connectors)
Setting Value All (default)/ Received Audio only
All: Enables output of beep tone, voice guidance, audio of voice
message memory and recorded audio or sidetone.
Received Audio Only: Select this setting when having an
external device decode the digital modulation signals.
When the RX audio is mixed with the beep tone, voice
guidance or error tone emitted from this transceiver, the
command response or error tone produced by this
transceiver can also be heard at a remote location during,
for example, KNS (KENWOOD NETWORK COMMAND
SYSTEM) operation with this transceiver installed at a
remote location.
Audio output to LAN is used for the purpose of listening
to the audio output from the transceiver speaker on a
remote PC during remote operation. As such, audio such
as the beep sound is always mixed regardless of the
setting in this menu.
OTHER FUNCTIONS 16
16-7
165


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info