683161
164
Zoom out
Zoom in
Previous page
1/196
Next page
Saving a Screen Shot
This transceiver comes with a screen capture function to capture
an image of the screen display and save the image data in the PNG
format (.png) to the built-in memory or a USB flash drive.
1 Assign “Capture” to a PF key.
To save the image data to a USB flash drive, insert a USB
flash drive into (USB-A).
2 Press PF [Capture].
The memory icon being selected as the storage destination
blinks. A shot of the screen is captured at the same time
when the key is pressed, and the captured data is saved to
a USB flash drive. The directory of the storage destination
is “KENWOOD\TS-890\CAPTURE”.
When removing the USB flash drive, make sure to execute
Safely Removing the USB Flash Drive” (11-6).
The saved file is named as follows.
yyyymmdd_hhmmss.png
(Example)
20180215_102030.png
(When the screen shot is saved on February 15, 2018,
10:20:30 a.m.)
When saving the screen capture to a USB flash drive,
check the following in advance.
The USB flash drive is formatted by this transceiver.
The USB flash drive is correctly inserted into this
transceiver.
There is sufficient free space on the USB flash drive.
The USB flash drive is not write-protected or the file
system is not corrupted.
A screen shot can also be captured and saved by
pressing [Print Screen] on the USB keyboard.
A screen shot cannot be captured when the screen saver
is active.
When screen capture fails, an error tone is output.
It might take some time before the captured image is
written to a USB flash drive. If there is an attempt to safely
remove the USB flash drive, a message will be displayed
asking the user to wait until the captured image file is
saved to the USB flash drive before attempting to remove
it.
Configuring Output to an External Meter
The TX or RX signal level can be displayed by connecting an
analog meter to the METER terminal on the rear panel of this
transceiver. A different output signal format can be configured for
each of External Meter 1 and External Meter 2.
The signal to be output to the external meter during transmission
can be configured as follows. During reception, the signal strength
will be output as signals to the external meter.
Output rating of METER terminal:
Voltage: 0 to 5 V (no load)
Impedance: 4.7 kΩ
Configuring the Output Signal Format of the External
Meter
Configure the signal that is output from the METER terminal to the
external meter.
Configure in Advanced Menu [0] Indication Signal
Type (External Meter 1) (External Meter 1) or
Advanced Menu [1] Indication Signal Type
(External Meter 2) (External Meter 2)
Setting Value
Automatic (default: External Meter 2)/ TX Power
(default: External Meter 1)/ ALC/ Drain Voltage
(Vd)/ Compression Level (COMP)/ Current (Id)/
SWR
Automatic: Outputs the S meter level during reception, and the
signal level or meter value displayed on F [METER] during
transmission.
TX Power: Outputs the TX output power value.
ALC: Outputs the ALC level.
Drain Voltage (Vd): Outputs the drain voltage of the final FET.
Compression Level (COMP): Outputs the degree of audio
signal enhancement by the speech processor.
Current (Id): Outputs the drain current of the final FET.
SWR: Outputs the standing wave ratio (SWR).
Configuring the External Meter Output Level
External Meter 1 and External Meter 2 can be configured to
different signal levels that are output from this transceiver
according to the rating of the external meter that is connected to
the METER terminal.
Configure in Advanced Menu [2]
Output Level
(External Meter 1) (level of external meter output
1) or Advanced Menu [3] Output Level (External
Meter 2) (level of external meter output 2)
Setting Value 0% to 50% (default) to 100% (1 step)
At “100%”, the voltage is 5 V.
16 OTHER FUNCTIONS
16-6
164


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info