683161

Kenwood TS-890S Manual

169
Zoom out
Zoom in
Previous page
1/196
Next page
TX Inhibit
This function prevents erroneous transmission. When TX Inhibit is
ON, this transceiver does not carry out transmission even when
[PTT] on the microphone is pressed.
The RX audio also becomes inaudible while [PTT] is pressed.
Inhibit transmission in the following cases.
•
When you want to operate the master transceiver unit as a
receive-only unit during operation in the Split Transfer B mode.
Transmission is not carried out even when this is attempted
using the master transceiver. Audio is also not output.
•
When you do not wish to transmit signals to the host transceiver
while controlling the transceiver via PC using KNS (KENWOOD
NETWORK COMMAND SYSTEM).
Configure in Menu [6-03] “TX Inhibit”
Setting Value Off (default)/ On
●
When TX Inhibit is ON, RX audio is muted when the SS
terminal signal level of the ACC 2 connector is low. RX
audio is also muted while [PTT] is pressed as the signal
level of the SS terminal becomes low.
●
When TX Inhibit is ON, tuning cannot be performed by
the antenna tuner.
●
When using this transceiver as a receive-only unit at all
times, configure this setting to “On” to prevent erroneous
transmission.
Packet Cluster Tuning
Packet cluster tuning can be performed by connecting TM-
D710(A/E), TM-D710G(A/E), RC-D710, TM-D700(A/E) or TH-
D72(A/E) to this transceiver.
Connection
.
78
TH-D72(A/E)
Φ2.5mm-Three-pronged Plug
COM Terminal
GND
TXD
RXD
(Female)
9-pin D-SUB Connector
(Solder Side)
9-pin D-SUB
Female
TM-D700(A/E)
PG-5G
RC-D710 + PG-5J
TS-890S
RC-D710 + TM-V71(A/E)
TM-D710(A/E), TM-D710G(A/E)
9-pin D-SUB Male
9-pin D-SUB Female
Receiving Packet Cluster Data
Follow the steps below to operate TM-D710(A/E)/RC-D710/TM-
D700(A/E)/TH-D72(A/E).
1 Switch to the APRS or Navitra mode to receive the
DX packet cluster data.
2 Display the DX packet cluster and align the cursor
with the frequency to tune to.
3 Press the corresponding key to output the
frequency value selected in step 2.
The operating frequency (VFO) is configured based on the
packet cluster data received if the frequency is configurable by
this transceiver.
•
TM-D710(A/E), TM-D710G(A/E), RC-D710: [TUNE] key
•
TM-D700(A/E): [MHz] key
•
TH-D72(A/E): [MENU] key
●
In the VFO mode, the operating frequency (VFO) that is
currently in use is configured. In the memory channel
mode, the most recent operating frequency (VFO) is
configured.
●
Only the RX data sent from TM-D710(A/E)/TM-
D710G(A/E)/RC-D710/TM-D700(A/E)/TH-D72(A/E) is
supported.
●
DX packet cluster data cannot be sent out automatically
to this transceiver.
●
For TM-D700(A/E), version G 2.0 or later is required to
use this function.
●
Production of the TM-D710(A/E), RC-D710 and TM-
D700(A/E) have been discontinued.
●
For more details on the operation information of the DX
packet cluster, please search for information available
on other sources.
OTHER FUNCTIONS 16
16-11
… 169 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info