683161
155
Zoom out
Zoom in
Previous page
1/196
Next page
Configuration Using ARHP-890
To manage remote users and perform login authentication using
ARHP-890 as with the TS-990S, TS-590S, and TS-590SG,
configure the system as shown in Figure 3.
.
TS-890S
Host PC with
ARHP-890
Remote PC with
ARCP-890
LAN Connection
Hub
Broadband
Router
Broadband
Router
Internet
Figure 3: System Configuration for Remote User
Management and Login Authentication via ARHP
Under this configuration, the registered users list is managed by
the ARHP-890. ARHP-890 performs login authentication of the
remote user, while at the same time logs in to the TS-890S as an
administrator. After logging in, command communication and
voice communication between the TS-890S and ARCP-890 are
relayed.
The built-in VoIP of TS-890S is used for voice communication
(ARVP-10 or a non-KENWOOD VoIP can also be used for voice
communication).
It is necessary to configure the settings to transmit
incoming control commands and VoIP data via Internet
from the broadband router to each device. Please refer
to the “TS-890S KENWOOD NETWORK COMMAND
SYSTEM Setting Manual”.
Configuration for KNS Operation in a Home LAN
Environment
To operate the TS-890S remotely in a home LAN environment,
configure the system as shown in Figure 4.
.
TS-890SARCP-890
LAN Connection
Hub
Broadband Router
Figure 4: KNS System Configuration in a Home LAN
Environment
Under this configuration, ARCP-890 logs in to the TS-890S as an
administrator (login as a registered user is also possible).
The built-in VoIP of TS-890S is used for voice communication.
It is also possible to make use of the USB audio function by
connecting a USB cable (ARUA-10 is needed).
Another alternative option is to extract analog audio output
signal (ANO) and analog audio input signal (ANI) from the ACC
2 connector and connect to the audio input/output connector of
the PC sound card.
Configuring for KNS Operation
LAN Connection Settings
Follow the steps below to configure the LAN connection
environment for KNS operation.
1 Press [MENU].
2 Press F [KNS].
The KNS status screen for confirming the settings is displayed.
If F [KNS] is not displayed, press F [MORE] to display F
[KNS].
3 Press F4 [CONFIG].
The KNS configuration screen appears.
.
4
Press F2 [ ]/ F3 [ ] to select KNS Menu [0]
KNS Operation (LAN Connector).
5 Press F4 [SELECT].
6 Press F2 [–]/ F3 [+] to select the setting.
Setting Value Off (default)/ On (LAN)/ On (Internet)
On (LAN): When operating KNS in a home LAN environment.
On (Internet): When operating KNS via the Internet.
Pressing F [KNS TOP] returns the display to the KNS status
screen.
The KNS Operation cannot be changed to a value other
than “Off” without first configuring the administrator
settings
Administrator Settings
Administrator refers to the owner of the radio equipment (manager
of the radio equipment in the case of a club station).
To connect the transceiver to LAN and perform remote
operation from a PC via LAN, login authentication is needed.
An administrator ID and password are configured for the
transceiver in advance by the administrator, which are then
used to log in to the transceiver from ARCP-890.
Upon logging in with the administrator ID, the KNS menu can
be operated from ARCP-890.
1
Select KNS Menu [1] Administrator ID and KNS
Menu [2] Administrator Password.
2 Press F4[EDIT].
NETWORK/KNS OPERATION 15
15-3
155


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info