683161
125
Zoom out
Zoom in
Previous page
1/196
Next page
Reading Settings Data
Follow the steps below to read the settings data file of the
transceiver that is stored in the built-in memory or a USB flash
drive.
To read data from a USB flash drive, insert the USB flash drive
containing the settings data into (USB-A).
1 Press [MENU].
2 Press F [USB/FILE] to display the USB/File
Management menu screen.
If F [USB/FILE] is not displayed, press F [MORE] to display
F [USB/FILE].
3
Press F2 [ ]/ F3 [ ] to select Read
Configuration Data.
4 Press F4 [SELECT].
A screen for selecting the file (DATA) to read appears.
.
Information of the location to read files from (built-in memory
or USB flash drive) that was last selected on this screen is
displayed. However, if a USB flash drive is not connected or
cannot be correctly recognized, information of the built-in
memory will be displayed.
If no file is found, No file is found. is displayed on the
screen.
5 Select the file to read.
To read data from the internal memory, press F7 [INT.MEM].
To read data from the USB flash drive, press F7
[USB.MEM]. (If a USB flash drive is not connected, a message
will appear prompting you to get ready the USB flash drive.)
Pressing F5 [NAME] allows the file name to be changed.
Pressing F6 [DELETE] displays a message to confirm
deletion of the file. Pressing F4 [OK] deletes the file.
6
Press F2 [ ]/F3 [ ] or turn the [MULTI/CH]
control to select the settings data file to read.
7 Press F4 [OK] to display the selection screen
(DATA) for reading the data.
Pressing F7 [CANCEL] ends the operation without reading
a file.
.
8
Press F2 [ ] or F3 [ ], or turn the [MULTI/CH]
control to select a function group to read.
9
Press F5 [ ] to select the checkbox to the left
of the settings data name.
Pressing F5 [ ] again deselects the checkbox.
(Settings data will not be read.)
10 Repeat steps 8 and 9 to select the corresponding
checkboxes for the settings data to read.
11 Press F4 [OK] to start reading the files.
Reading of settings data files with a check mark starts. When
reading starts, a reading in progress screen is displayed.
Pressing F7 [CANCEL] exits the file selection screen
without starting reading and returns the display to the USB/
File Management menu screen.
After the settings data files have been read successfully, a
message indicating that reading is complete is displayed.
12 Press F4 [OK] to end the process.
This transceiver reboots automatically.
Data that are not created by this transceiver cannot be
read.
The following function groups can be excluded from the
reading process.
“Environmental Dependent” data (settings data that
are dependent on the installation environment)
Antenna selection data and preset data of antenna
tuner
Settings for items in menu group 6 (settings related
to the rear terminals)
Advanced menu settings
Linear amplifier menu settings
Transverter settings
LAN menu settings
KNS menu settings and KNS registered users’ list
Clock menu settings
“CW/RTTY/PSK Message Memory” data (CW/RTTY/
PSK message memory)
“Voice Message Memory” data (voice message data)
If the settings data file is saved in a transceiver with a
newer firmware version, pressing F4 [OK] in step 7 will
result in an error. A “data reading error screen due to
mismatch between new and old firmware versions” is
displayed and reading is not executed.
If the settings data file is corrupted, pressing F4 [OK] in
step 7 will result in an error. A “file reading NG screen” is
displayed and reading is not executed.
If data mismatch is detected after reading a settings data
file, a “corrupted data is detected screen” is displayed.
When this occurs, pressing F4 [OK] runs a full reset and
reboots this transceiver.
USB/FILE MANAGEMENT 11
11-3
125


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info