683161
103
Zoom out
Zoom in
Previous page
1/196
Next page
Deleting a Registered Frequency
1
Press F2 [ ]/ F3 [ ] or turn the [MULTI/CH]
control to select the frequency to delete.
2 Press and hold F5 [(DELETE)] to delete.
Turning ON/OFF Marker Function
1 Press [MENU].
2 Press F [F.MKR].
If F [F.MKR] is not displayed, press F [MORE] to display F
[F.MKR].
Pressing F [F.MKR] each time toggles the marker function
between ON and OFF.
Displaying the Maximum Value in the Waveform
The maximum value of the waveform shown on the spectrum
scope screen can be displayed to get a better grasp of the signal
status.
Turning ON/OFF Maximum Value Display
Press F1 [MORE] followed by F7 [MAX.HLD].
Pressing F7 [MAX.HLD] each time toggles the maximum value
display between ON and OFF.
Configuring the Hold Type
Select the method of displaying the maximum value of the waveform.
Configure in Menu [8-02] Bandscope Maximum Hold
Setting Value
10 [s] (default)/ Continuous
10 [s]: Maximum value information is cleared after 10 seconds.
Continuous: Maximum value information is not cleared.
The maximum value information is cleared automatically
if the range of the span displayed changes regardless of
whether “10 [s]” or “Continuous” is selected.
Pausing the Waveform Display
The waveform display on the bandscope screen can be paused.
Press F7 [PAUSE] to pause the waveform display.
When the waveform display is paused, << >> is
displayed on the screen.
.
Pressing F7 [PAUSE] again cancels the paused state.
Averaging of Spectrum Scope Waveform
Averaging the waveform on the spectrum scope smoothens the
changes in the waveform display making it easier to observe the
intermittent signals.
Press F1 [MORE], then press F6 [AVE.] to switch the
averaging level.
Pressing F6 [AVE.] each time switches the selection in the
following sequence: “Off” (averaging disabled) → “1”
(minimum) → “2” → “3” (maximum) → “Off”. The averaging
level selected is displayed at the top right corner of the grid.
Pressing and holding F6 [AVE.] each time switches the
options in the reverse sequence.
The averaging level can be configured separately for audio
mode (SSB/AM/FM (including DATA mode)) and non-audio
mode (CW/FSK/PSK).
The default settings of the audio mode and non-audio mode
are “2” and “1” respectively.
Displaying the TX Signal Waveform
A waveform for the TX signal can be displayed when a bandscope
for transmission is displayed in the Center mode.
Configure in Menu [8-00] Bandscope Display
during TX
Setting Value Off (default)/ On
On: Displays the TX waveform in the bandscope while
transmission is in progress.
Off: Does not display the waveform in the bandscope while
transmission is in progress.
The setting for this function cannot be switched while
transmission is in progress.
SCOPE FUNCTIONS 7
7-7
103


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info