683161
102
Zoom out
Zoom in
Previous page
1/196
Next page
Touchscreen Tuning
This function enables signals to be received by touching the
desired point in the spectrum scope display area or waterfall
display area.
When in the Auto Scroll mode and Fixed mode, touching a point
moves the marker to the corresponding frequency.
When in the Center mode, touching a point sets the
corresponding frequency as the center frequency.
.
Turning ON/OFF Touchscreen Tuning
Configure in Menu [0-14] Touchscreen Tuning
Setting Value Off/ On (default)
The following operations are prohibited even when
touchscreen tuning is ON.
When the frequency lock function is ON.
When the memory channels are empty or when
temporary change of memory channels is disabled.
When an area outside the frequency range of the
memory channel for specific band segments is
touched.
During transmission.
When the TX frequency is received by TF-SET while
only XIT is ON during simplex operation.
Correction steps for touchscreen tuning
Touch with a finger on the corresponding point in
the spectrum scope or waterfall display screen
where signal is to be received.
Step correction is performed according to the frequency step
size of the [MULTI/CH] control configured in Menu [3-01] to
[3-05] for each mode.
Touching and holding in the CW mode activates the CW auto
tune function.
Step correction is always performed in the FM/AM mode.
For the SSB/CW/FSK/PSK mode, configure to turn ON/OFF
the step correction operation in Menu [8-7] as follows.
Turning ON/OFF Step Correction
Configure to turn ON/OFF the step correction operation during
touchscreen tuning in the SSB/ CW/ FSK/ PSK mode.
Configure in Menu [8-07] Touchscreen Tuning Step
Correction (SSB/ CW/ FSK/ PSK)
Setting Value Off/On (default)
TX/RX Frequency Marker Display
The positions of the TX and RX frequencies are indicated as
markers on the bandscope screen.
During split operation, the TX frequency can be changed easily by
moving the TX frequency marker to the desired frequency while
monitoring the bandscope screen.
The markers are color coded as follows.
White: RX Frequency
Red: TX Frequency
The RX frequency before TF-SET is performed appears
as purple line while [TF-SET] is pressed.
Registering Frequency Marker
When a preferred frequency (up to 50 entries) is registered to the
frequency marker list, the registered frequency is indicated by a
marker on the bandscope (white dotted line). Registering the edge
frequency of the frequency band used in a band plan or during
contesting makes it easier to check the edge frequency on the
bandscope.
1 Press [MENU].
2 Press and hold F [F.MKR] to display the Frequency
Marker list screen.
If F [F.MKR] is not displayed, press F [MORE] to display F
[F.MKR].
.
3 Align with the frequency to register.
4 Press F4 [ADD] to register.
The current VFO frequency is added to the list.
When RIT is ON, the display frequency with RIT added is
registered.
The list is automatically sorted in ascending order starting
from the lowest frequency.
If the frequency to be added is already registered, it will not
be registered twice and there will be no response even when
F4 [ADD] is pressed.
If there are already 50 frequency entries in the list, the
frequency will not be registered and pressing F4 [ADD] will
have no response.
7 SCOPE FUNCTIONS
7-6
102


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info