683161
85
Zoom out
Zoom in
Previous page
1/196
Next page
Operation in Narrow FM Mode
It is possible to switch to a narrow bandwidth during operation in
the FM mode. The occupied bandwidth and maximum modulation
factor are shown in the table below. Selecting FM Narrow
according to the modulation factor of the target station helps to
avoid distortion and deterioration in the clarity of the RX audio.
Mode Occupied Bandwidth
Maximum Modulation
Factor
FM (Wide) 16 kHz or lower ±5 kHz or lower
FM Narrow 10 kHz or lower ±2.5 kHz or lower
Press and hold [FM/AM].
Pressing and holding [FM/AM] each time switches between
“FM” and “FMN (Narrow)”.
.
Operating the FM Repeater
Switching this transceiver to split operation and turning on the tone
signal while in the FM mode enables this transceiver to be used in
the repeater operation mode.
.
88.5 Hz
29.520 MHz
29.620 MHz
29.620 MHz
88.5 Hz
29.520 MHz
Configuring the Tone Signal
Registering the tone settings to a memory channel and
calling up the frequency or operation information from
the memory channel eliminates the need to configure the
tone frequency each time. For more details on the
memory channel settings, please refer to “MEMORY
CHANNELS” (9-1).
The tone frequency may vary depending on the country
or region this transceiver is being used.
Selecting a Tone
Press F4 [TONE] to select “TONE”.
Pressing F4 [TONE] each time toggles the tone signal selection
in the following sequence: “TONE” → “CTCSS (CT)” →
“CROSS” → Blank (deselected).
.
Configuring the Tone Frequency
1 Press and hold F4 [TONE] while “TONE” is selected
to display the FM Tone Frequency screen.
.
2 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to select the tone frequency.
Tone Frequency (Hz)
67.0 88.5 114.8 151.4 177.3 203.5 250.3
69.3 91.5 118.8 156.7 179.9 206.5 254.1
71.9 94.8 123.0 159.8 183.5 210.7 1750
74.4 97.4 127.3 162.2 186.2 218.1
77.0 100.0 131.8 165.5 189.9 225.7
79.7 103.5 136.5 167.9 192.8 229.1
82.5 107.2 141.3 171.3 196.6 233.6
85.4 110.9 146.2 173.8 199.5 241.8
The default setting is “88.5 Hz”.
To restore the default setting, press and hold F1
[(RESET)].
3 Press [ESC] to end the process.
Tone Frequency Scan
Tone frequency that is contained in signals received in the FM
mode can be searched and displayed with the following steps. This
is useful when there is a need to know the tone frequency of the
repeater station.
1 Press and hold F4 [TONE] while “TONE” is selected
to display the FM Tone Frequency screen.
2 Press F7 [SCAN] to start tone frequency scan.
Scanning stops when a tone frequency is detected, and the
frequency is displayed in the “FREQ. [Hz]” field.
Pressing F7 [SCAN] while tone frequency scan is in
progress stops the scan operation. Pressing F7 [SCAN]
again resume scanning.
The scan operation stops when the RX signal is interrupted
during tone frequency scan. Scanning resumes when a RX
signal is detected by this transceiver.
3 Press [ESC] to end the process.
COMMUNICATING AIDS 5
5-29
85


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info