683161
87
Zoom out
Zoom in
Previous page
1/196
Next page
Attenuator
The attenuator is a function for attenuating the RX signals. If there
is interference due to strong signals near the target signal, turning
on the attenuator helps to reduce interference caused by nearby
frequencies.
It is also effective in situations where the RX audio is distorted
when the RX signal is too strong. This transceiver comes with three
different types of attenuators.
Press F [ATT].
Pressing F [ATT] each time switches the attenuation level.
Setting Value Off (default)/ 6 dB/ 12 dB/ 18 dB
Pressing and holding F [ATT] each time switches the options
in the reverse sequence.
The attenuation level is stored for each antenna selection
band.
The status of the attenuator (attenuation level) is displayed
in the key guide.
.
Switching the RX Filter Band Characteristics
Switching the RX Filter (A, B, C)
The setting for the band characteristics of the RX filter on this
transceiver can be switched at one touch according to the
operating status to one of the three types (A, B or C).
The band characteristics are configured by combining the
roofing filter or IF and AF filter, high cutoff/low cutoff and WIDTH/
SHIFT. A different RX filter setting (A, B or C) can be stored for
each of the SSB, CW, FSK, PSK, FM and AM modes.
Press [IF FIL].
Pressing [IF FIL] each time switches the RX filter in the order
of “A”, “B” and “C”.
The selected filter is displayed at the top left of the filter
scope.
The RX filter does not switch to Type C if Menu [6-10] RX
Filter Numbers below is configured to “2”.
Configuring the Selectable Types of RX Filters
The selectable types of RX filters can be configured to three (A, B
and C) or two (A and B).
Configure in Menu [6-10] RX Filter Numbers
Setting Value
2/ 3 (default)
Filter Scope
The following information is displayed on the filter scope screen.
Selected RX filter (A, B or C)
Image of the RX filter passband characteristics (trapezoid)
Audio spectrum of the RX audio
Parameters including the IF filter passband width
Pitch frequency in the CW mode
Notch point of the notch filter
Passband width of the roofing filter
.
SSB
AM/FM
PSK
FSK
CW
The audio spectrum is not shown on the filter scope while
the audio scope screen is displayed.
The audio spectrum is not shown on the filter scope while
the RTTY/PSK communication screen is displayed.
An out-of-range marker
is displayed when the
image of the passband cannot be displayed within the
display area because the shift amount of the filter in the
CW mode is large.
The audio spectrum is usually displayed within the image
of the passband. However, it may be displayed beyond
the image of the passband if there are excessively high
input signals.
When the notch filter is ON, the indicator representing
the notch point is displayed in white. The indicator is
displayed in white when the notch point is on the positive
side of the carrier wave in the AM mode. If the notch point
moves towards the minus side of the carrier wave, the
indicator changes to orange and moves from the left
edge of the screen to the right edge.
REJECTING INTERFERENCE 6
6 REJECTING INTERFERENCE
6-1
87


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info