683161
84
Zoom out
Zoom in
Previous page
1/196
Next page
Displaying a Time Stamp
A time stamp is inserted when there is a change in the encoding
or decoding status.
Selecting a Time Stamp Type
It is possible to select whether to display only the time stamp or to
display both the time stamp and frequency.
Configure in Menu [2-15] CW/RTTY/PSK Time
Stamp
Setting Value
Off/ Time Stamp/ Time Stamp+Frequency
(default)
Off: Does not display a time stamp.
Time Stamp: Displays only the time stamp.
Time Stamp+Frequency: Displays both the time stamp and
frequency.
Selecting a Clock Type
Configure the clock for displaying the time stamp to a “Local Clock”
or “Secondary Clock”.
Configure in Menu [2-16] Clock (CW/RTTY/PSK
Time Stamp)
Setting Value Local Clock (default)/ Secondary Clock
When encoding or decoding starts, a line break and time
stamp will be inserted before displaying the encoded or
decoded character string.
Editing the Communication Log File
1 In the CW communication screen, press and hold
F2 [LOG]. In the RTTY and PSK communication
screens, press and hold F4 [LOG].
The screen for selecting log file appears.
.
2
Press F2[ ]/ F3[ ] to select a file.
Pressing F4 [VIEW] displays the log information of the
selected file.
.
To read data from the internal memory, press F7 [INT.MEM].
To read data from the USB flash drive, press F7
[USB.MEM]. (If a USB flash drive is not connected, a message
will appear prompting you to get ready the USB flash drive.)
Pressing F5 [NAME] allows the file name to be changed.
Pressing F6 [DELETE] displays a message to confirm
deletion of the file. Pressing F4 [OK] deletes the file.
Operation in FM Mode
Operating in the FM mode enables high-quality voice
communication as well as communication that is noise-resistant.
Communication in the FM mode is also supported on the 29 MHz,
50 MHz and 70 MHz (E type) bands. To communicate with a
distant station for which communication cannot be established
directly, do so via a repeater.
Adjusting Microphone Gain during Operation in FM
Mode
1 Adjust the frequency.
2 Press [FM/AM/FM-N] to select FM mode.
3 Press [MENU].
4 Press F [ADV.] to display the Advanced Menu
screen.
If F [ADV.] is not displayed, press F [MORE] to display F
[ADV.].
5
Select Advanced Menu [10] Microphone Gain (FM
Mode).
6 Press [SEND], or press and hold [PTT] on the
microphone.
This transceiver is placed in the TX mode and a level meter is
displayed.
7 Speak into the microphone in the normal tone and
loudness.
8 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to adjust the microphone gain.
Setting Value 0 to 50 (default) to 100 (1 step)
Adjust the microphone gain level such that the peak value
of the level meter falls within the zone.
9 Press [SEND] or release [PTT] on the microphone.
Doing so places this transceiver in the RX mode.
10
Press F1 [ ].
When using a microphone with a low sensitivity such as
the MC-90, adjust the microphone gain to a higher level.
When a microphone with a low sensitivity is used, the
modulation factor may stabilize by setting the speech
processor to ON.
5 COMMUNICATING AIDS
5-28
84


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info