683161
80
Zoom out
Zoom in
Previous page
1/196
Next page
FFT Scope/Vectorscope Display Setting
The tuning scope displayed on the PSK communication screen
can be switched to an “FFT scope” or “vectorscope” display.
Configure in Menu [2-13] PSK Tuning Scope
Setting Value FFT Scope (default)/ Vector Scope
The display toggles between the “FFT scope” and “Vector
Scope” each time the scope display on the screen is touched.
FFT Scope Waveform Averaging
The waveform displayed on the FFT scope can be averaged.
Averaging of the waveform reduces random noise and makes
observation of the target signal easier.
Configure in Menu [2-10] FFT Scope Averaging
(PSK Decode)
Setting Value
0 (default) to 9 (1 step) (minimum to maximum
averaging)
Selecting a Waterfall Display Type
Configure in Menu [2-17] Waterfall when Tuning
(RTTY/PSK Audio Scope)
Setting Value Straight (default)/ Follow
Straight: Uses a straight line to show transition in the level of
the target signal displayed on the waterfall when the RX
frequency is altered.
Follow: Tracks and displays the latest FFT scope level at the
portion where the waterfall starts flowing when the RX
frequency is altered.
Vectorscope
Turn the Tuning control to perform tuning such that the emission
lines displayed on the vectorscope radiate from the center into the
same direction.
.
Unmodulated Carrier SignalIdle Signal of BPSK or QPSK
In Tune (QPSK)In Tune (BPSK)
Make use of the fine-tuning function if there is difficulty
in performing tuning.
While transmission is in progress, the vectorscope does
not function and points to the 12 o’clock direction.
AFC (Automatic Frequency Control)
The AFC (Automatic Frequency Control) function can be used to
tune the PSK signal that is being received.
Press F6 [AFC] to set the AFC function to “On”.
Pressing F6 [AFC] each time toggles the option in the
following sequence: “OFF” → “AFC ON” →“ AFC&NET ON”
→ “OFF”.
When the AFC function is ON, the << >> display lights
up. The amount of frequency correction made by the AFC
function is displayed below “AFC”.
Pressing and holding F6[AFC] while the AFC function is ON
increases or decreases the displayed frequency which
indicates the amount of correction made by the AFC
function.
.
Configuring the AFC Tuning Range
Configure the frequency range for tuning the PSK signals that are
received using the AFC function.
Configure in Menu [2-11]
PSK AFC Tuning Range
Setting Value ±8/ ±15 (default) [Hz]
NET
The NET function transmits signals by applying the frequency that
is automatically tuned by AFC.
Press F6 [AFC] to select “AFC & NET”.
Pressing F6 [AFC] each time toggles the option in the
following sequence: “OFF” → “AFC function ON” →“ AFC
function & NET function ON” → “OFF”.
<< >> and << >> light up.
.
Switching between BPSK and QPSK
The PSK mode is further divided into 2 sub-modes, namely BPSK
and QPSK. BPSK is the more commonly used mode. QPSK excels
at correcting errors and boasts a higher decoding rate than BPSK.
Press F2 [B/QPSK].
Pressing the key each time toggles the mode between BPSK
and QPSK. The display to the right of the status bar toggles
between << >> and << >> when the mode is
switched.
This is fixed at BPSK when the PSK63 mode is selected.
5 COMMUNICATING AIDS
5-24
80


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info