683161
78
Zoom out
Zoom in
Previous page
1/196
Next page
Frequency Reverse in RTTY Mode
Decoding cannot be performed correctly when the RTTY signal
received is in the reverse state (frequencies of the mark signal and
space signal are reversed). When this occurs, press and hold
[FSK/ PSK] to reverse the RTTY signal received so that the
reverse signal can be decoded.
.
Space
Frequency
Mark
Frequency
BFOBFO
Mark
Frequency
Space
Frequency
170 Hz2125 Hz2125 Hz170 Hz
ReverseNormal
Operating RTTY (FSK) Using an External Device
To operate in the RTTY mode using a PC or other external devices
(such as RTTY device or PC connection interface) instead of the
built-in encoder and decoder functions of this transceiver while this
transceiver is configured to the RTTY (FSK) mode, connect using
the USB port or ACC 2 connector on the rear panel of this
transceiver.
When connecting to a PC (using the USB port)
RTTY keying: Configure the USB keying function to RTTY
Keying.
TX control: Use PC commands (TX; to start transmission
and RX; to end transmission). Or configure the USB keying
function to PTT.
Audio output: Select “USB AUDIO CODEC” for the recording
device using the sound setting on the PC.
For more details on the USB keying function, please refer to
USB Keying” (16-12).
When connecting to other external devices (using the
ACC 2 connector)
RTTY keying: Connect pin 2 (RTTY) of the ACC 2 connector
to the keying output line of the external device.
TX control: Connect pin 13 (SS) of the ACC 2 connector to
the TX control (PTT) line of the external device.
Audio output: Connect pin 3 (ANO) of the ACC 2 connector
to the demodulation input line of the external device.
* For more details on the ACC 2 connector, please refer to
ACC 2 Connector” (1-7).
For more details on other connections and settings, please refer
to “PC Connection for Data Communication” (1-4).
RTTY (FSK) Keying Polarity Setting
Configure in Menu [2-07]
FSK Keying Polarity
Setting Value Off (default)/ On
Configure the RTTY keying polarity according to the
specifications of the external device. When Menu [2-07]
FSK Keying Polarity is configured to “Off” and pin 2 (RTTY)
is short-circuited to GND, signals are transmitted at the mark
frequency configured in Menu [2-08] FSK Tone
Frequency.
When Menu [2-07] FSK Keying Polarity is configured to
“On”, signals are transmitted as space signals with the mark
frequency shifted by the amount configured in Menu [2-06]
FSK Spacing.
Audio Peak Filter
Using the audio peak filter may help to improve the decodability of
RTTY messages when operating in the RTTY (FSK) mode with
this transceiver connected to an external device.
Press F [APF] to set the audio peak filter to ON.
When audio peak filter is turned on, “ON” is displayed in the
lower row of F [APF].
When audio peak filter is turned off, “OFF” is displayed in the
lower row of F [APF].
PSK Operation
This transceiver is equipped with a built-in demodulator, encoder
and decoder for operating in the PSK31 and PSK63 modes.
Operation in the PSK31 or PSK63 mode can be performed easily
by connecting a commercially available USB keyboard. PSK can
also be operated using a data communication software program
that makes use of the sound function of a PC.
When transmitting in the PSK mode, adjust the carrier
until the ALC meter starts to deflect.
When an external device is used, adjust the audio signal
level from the external device, followed by adjusting the
ALC meter until it starts to deflect.
Displaying the PSK Communication Screen
1
Press [FSK/PSK] to select PSK mode.
2
Press F3 [DECODE].
The PSK communication screen appears.
Text Display Area + FFT Scope
.
Text Display Area + Vectorscope
.
Switching between the FFT Scope and Vectorscope Display
The display toggles between the “FFT scope” and “Vector Scope”
each time the scope display on the screen is touched.
Noise Reduction 1, Noise Reduction 2, Beat Canceler 1,
Beat Canceler 2 and RX DSP equalizer do not function
during decoding of PSK messages.
5 COMMUNICATING AIDS
5-22
78


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info