606693
72
Zoom out
Zoom in
Previous page
1/104
Next page
66
11 OPERATOR CONVENIENCES
Receiving Data
There are two ways that the Slave can receive the
data from the Master:
Quick memory 1
(TS-450S/690S: channel 00), or
VFO
This choice is made on the Slave transceiver. On
the TS-870S, Menu No. 55 (DIRECT) can be set to
OFF to receive data into Quick memory, or to ON to
receive data in a VFO. Check your Instruction
Manual for other transceivers. Set Menu No. 27
(TX INH) to ON for a Slave TS-870S.
When receiving data at the Slave transceiver in the
VFO, the data is transferred to the TX side of the
VFO that is currently selected. If the transferred
frequency is simplex, both the RIT and XIT on the
Slave are set to OFF; if a split frequency is
transferred then XIT is set to OFF but RIT is not
changed on the Slave. The IF filter is determined by
the transferred mode. AIP status is determined by
the transferred receive frequency according to the
AIP band memory.
If the Slave transceiver has a Quick or Conventional
memory channel recalled for transmit when the
transfer is done, the data will be rejected. To receive
data into a VFO, select TX and RX using VFOs.
Pin Name
1
2
3
4
5
6
GND
TX/RX
TX/RX
CTS
RTS
NC
Pin
No.
r
e
w
t
y
q
Rear Panel view on
TS-450S/690S/850S/950SDX
ACC 1
Connections
Connect each end of the interconnecting cable to
the COM connector or the ACC 1 connector on the
transceivers.
DSP-100 Users:
You may continue using your DSP-100
DSP Unit with the Transfer function. Connect the
interconnecting cable to either the CONT IN or CONT OUT
connector on the DSP-100, then connect the unused CONT
connector on the DSP-100 to the ACC 1 connector on the
transceiver. The transceiver connected to the CONT IN
becomes the Master; the transceiver connected to the
CONT OUT connector is the Slave.
USING QUICK TRANSFER
Note:
While transmitting data, other functions may work more
slowly.
Transferring Data
The Master is the transceiver that sends data to the
Slave transceiver. If the Master has the RIT function
switched ON, the RIT offset frequency is added to
the receive frequency to be transferred.
1 Switch ON the Transfer function on each
transceiver.
On the TS-870S, activate Menu No. 54
(TRNSFER) function. For the compatible
transceiver, check your Instruction Manual for
the correct method.
2 On the Master transceiver, press
QUICK MEMO [M.IN].
If the Master is a TS-450S/690S, press
[M.IN], select memory channel 00, then press
[M.IN] again.
The displayed receive data is stored in Quick
memory channel 1 on the Master transceiver
(TS-450S/690S: channel 00) and transferred
to the Slave transceiver.
w
e
t
u
i
w
e
t
u
i
TS-870S TS-870S
TS-870S
Cross-wired cable
Cross-wired cable
See IF-232C manual.
IF-232C
Straight cable
COM Connector
cable
TS-450S/690S/850S/950SDX
A
N
T
DIN(6P)
RS-232C(25P)
DIN(6P)
COM (9P)
COM (9P)
COM (9P)
E
X
T
R
X
A
N
T
E
X
T
R
X
A
N
T
72


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-870S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-870S in the language / languages: English as an attachment in your email.

The manual is 2,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-870S

Kenwood TS-870S User Manual - Dutch - 102 pages

Kenwood TS-870S User Manual - French - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info