686368

Kemppi A7 MIG Power Source 450 Manual

26
Zoom out
Zoom in
Previous page
1/67
Next page
26
A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
4.2.7 Robot settings
Robot menu (Menu 8/8)
Menu item Value range Factory setting Description
1/15 Interface mode * 1 - 99 15 Select the robot I/O table for the eldbus communication (digital robot interface).
2/15 Voltage scaling * 0 - 9999 0 (no scaling) Select the maximum value for welding voltage / ne tuning in scaled mode (1-9999), or switch scaled
mode o (0).
3/15 WFS scaling * 0 - 9999 0 (no scaling) Select the maximum value for wire feed speed in scaled mode (1-9999), or switch scaled mode o (0).
4/15 Current scaling * 0 - 9999 0 (no scaling) Select the maximum value for welding current in scaled mode (1-9999), or switch scaled mode o (0).
5/15 Simulation ON, OFF, USER OFF Select welding simulation on and o, or let the user of the robot to manage the simulation (USER).
6/15 Wire Feeder * WF1, WF2, USER WF1 Select the wire feeder in dual wire feeder systems.
7/15
Emergency stop
menu *
Congure emergency stop functionality. The emergency stop circuitry is connected to the robot
interface unit of the A7 MIG Welder.
Selection ON, OFF OFF Set the emergency stop input on and o.
Line level 0 V, 24 V 0 V Select the voltage level of the input line.
Switch type Opening, Closing Opening Select the type of the electrical switch used in the signal line. The opening type switch opens the
electrical circuit of the signal line and the closing type switch closes the circuit.
8/15
Door switch menu * Congure gate door functionality. The gate door circuitry is connected to the robot interface unit of the
A7 MIG Welder.
Selection ON, OFF OFF Set the gate door input on and o.
Line level 0 V, 24 V 0 V Select the voltage level of the input line.
Switch type Opening, Closing Opening Select the type of the electrical switch used in the signal line. The opening type switch opens the
electrical circuit of the signal line and the closing type switch closes the circuit.
9/15
Touch sensor menu * Congure touch sensor.
Voltage 50 V, 80 V, 110 V, 160 V,
170 V, 180 V, 200 V
50 V Select the output voltage level for the touch sensor.
Tool USER, Welding wire, Gas
nozzle
USER Select the tool used for touch sensing (welding wire or gas nozzle), or let the user of the robot to
manage the tool selection (USER).
FastOutput Low-act, High-act Low-act Select the signal polarity of the fast hardware output. The low-active signal pulls the output to 0 V on
logical ’1’ state and the high-active signal releases the output on logical ’1’. The signal is pulled up to 24 V
by a resistor when released.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 MIG Power Source 450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 MIG Power Source 450 in the language / languages: English as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info