Manual Kalkhoff Rohloff SpeedHub 500-14 (page 28 of 114) (English, German, Dutch, French, Italian)

780095

Zoom out

Zoom in

1/114

Bendthelongtorquearmsideways

untilthesmallendsitsdirectly

underneaththechainstay.

Placetherearwheelintothe

dropoutsandrotatetheaxle,so

thatthelongtorquearmsitsjust

underneaththechainstay.Closethe

quickreleaselever.

5. Mounting the wheel

5.1.1 with long torque arm

Mounting (CC versions)

Rohloff SPEEDHUB 500/14

The CC versions are equipped with a quick release block for the long torque arm to

enable a quick wheel removal. The quick release block must be secured to the chainstay.

Rohloff SPEEDHUB 500/14

Pushthelongtorquearmwiththe

attachedquickreleaseblock

againsttheundersideofthechain

stay. Theprotudingsideofthe

quickreleasepinmustface

inwards. Withtheaxlequick

releaseleverclosed,checkthatthe

quickreleaseblocksitsdirectly

underthechainstay.Ifnot,bend

thetorquearmintothecorrect

position.

Closedposition: Thequickrelease

pinisflushwiththeoutersideof

thequickreleaseblock(Fig.5). To

open:Pushthequickreleasepin

fromtheinnerside.

Insertthelocatingforkintothe

quickreleaseblockandpushthe

quickreleasepinin. Toeasethis

process,pullthetorquearmdown,

awayfromthechainstay.

Bothclampsshouldbebentaround

thechainstayintopositionas

showninthepictureabove. The

securingboltsoftheclampsmust

sitontheinsideoftheframe

facingdownwards.

Quickreleaseblock

Outer

side

Quickreleasepin

Inner

side

Mounting

Removetheclampsand(using

wirecutters)trimthemtothe

correctlength.Smallphoto:

Removethesharpedges(Riskof

injury).

Fitbothclampsandtightenthe

securingboltsevenly(tightening

torque: .).

2.5Nm/21,5in.lbs

Openthequickreleasepinandthe

axlequickreleaselever,checkthat

thelocatingforkcanbeeasily

swunginandoutofthequick

releaseblock.Ifnot,theclamps

mustbeloosenedandquickrelease

blockrelocatedaccordingly.

Mounting (TS versions)

The TS versions are equipped with a frame clamp for the long torque arm. This consists

of a metal clamp, nut, bolt and washer.

Rohloff SPEEDHUB 500/14

Placethemetalclampoverthe

chainstayandsecuretotheendof

thelongtorquearmwiththe

suppliedbolt.(10mmwrenchand

4mmallenkey-tighteningtorque:

6Nm/51in.lbs.).

Bendthelongtorquearmsideways

untiltheendsitsdirectly

underneaththechainstay.

Placetherearwheelintothe

dropoutsandrotatetheaxle,so

thatthelongtorquearmsitsjust

underneaththechainstay. Tighten

theaxlenuts.

Mounting

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kalkhoff Rohloff SpeedHub 500-14 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 40.9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kalkhoff Rohloff SpeedHub 500-14 Manual

Product: