778421
29
Zoom out
Zoom in
Previous page
1/70
Next page
Originalbetriebsanleitung Allgemein EN-29
Fig. 31 Straight front stem,
angle-adjustable
Screw
Fork steerer
Fig. 32 Ahead front stem,
angle-adjustable
Screw
Fork steerer
Spacer
1. Loosen the screw by two or three turns using an Allen
key until you can adjust the angle of the front stem.
2. Tilt the front stem to the desired angle.
3. To secure the front stem, tighten the screw clockwise
to the specied torque using a torque wrench 13.
Tightening torques for threaded connections Page EN-19.
19.3 Adjusting the height of the handlebars
How to determine the optimal handlebar height for your
body size:
1. Sit on the saddle and at the same time, lean against
a wall.
2. Lean your upper body towards the handlebars until
you nd a position that is comfortable for your back.
3. Extend your arms towards the handlebars.
4. Make a note of the approximate position of your hands
so that you can adjust the handlebars to this height.
19.3.1 Straight front stems: adjusting the
height of the handlebars
Warning
Serious falls due to a detaching, bending or breaking
front stem.
The front stem is marked with the maximum distance
that it can be drawn out of the fork steerer. Never
pull the seat post further out of the fork steerer than
the marking. If you cannot nd any marking, insert
the front stem to a depth of at least 6.5 cm in the
fork steerer.
1. Loosen the front stem spindle by turning it two or
three turns counterclockwise with an Allen key. To
prevent the bicycle fork from moving when loosening
the front stem spindle, grip the front wheel with your
knees.
Fig. 33 Front stem spindle
2. Take hold of the handlebars by the grips and turn them
alternately to the left and right. If this is not possible,
strike the front stem spindle gently from above with
a plastic hammer until the clamping device inside the
front stem releases.
3. Draw the front stem out of the fork steerer tube to the
desired height, but not higher than permitted.
4. Align the front stem with the front wheel so that they
form a right angle.
5. To secure the front stem again, tighten the front stem
spindle clockwise to the specied torque using a
torque wrench 13. Tightening torques for threaded
connections Page EN-19.
19.3.2 Ahead front stems: adjusting the
height of the handlebars
For Ahead front stems, any adjustment to the height of the
handlebars must be made by a specialist workshop.
19.4 Cleaning and care
The handlebars and front stem can be easily cleaned with a
slightly damp cloth.
20. Adjusting the position of the position
of the handlebar grips
The handlebar grips are tted to the ends of the bicycle
handlebars. They aect riding comfort and your health.
If your hands or wrists hurt after longer rides, it makes
sense to change the position of, or replace, the handlebar
grips. To replace the grips, contact your specialist
workshop. Models are available with and without threaded
connections. Grips with no threaded connection cannot be
easily adjusted, as they usually clamp very rmly onto the
ends of the handlebars. You should also contact a specialist
workshop about this, as attempting to change the position
of the grips can damage them. Screw grips are secured to
the handlebar with screws on the inside and outside, which
can be used to adjust the grips.
Fig. 34a Internal clamping
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kalkhoff 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kalkhoff 2021 in the language / languages: English as an attachment in your email.

The manual is 5.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kalkhoff 2021

Kalkhoff 2021 User Manual - German - 72 pages

Kalkhoff 2021 User Manual - Dutch - 71 pages

Kalkhoff 2021 User Manual - French - 74 pages

Kalkhoff 2021 User Manual - Spanish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info