Manual Jablotron JA-60 (page 22 of 34) (English)

555054

Zoom out

Zoom in

1/34

Alarm system JA-60 "COMFORT" - 22 - MDY51319

10. To enable a remote computer to dial in

When the user or installer wants to dial in to the installation from their JA-60U modem equipped computer or JA-60E keypad (see 15.),

the following parameters should be programmed in the control panel’s telephone dialer.

The most convenient programming of the dialer is via a connected PC using the Comlink software (see 14). Programming can also be

performed by entering programming sequences from the system keypad while in the control panel programming mode:

• Enter the programming mode (entering F 0 SC - SC = Service Code, factory default SC=6060), indicated by a „P“ on the display.

This can only be done while the panel is disarmed.

• The programming sequences can be entered from the keypad. Any unfinished sequence can be terminated by N key.

• To exit the programming mode, press the N key („P“ will turn off).

Dialing in parameters

Function sequence options

factory d.

note

Incoming call reaction

0 5 x

0=disabled, 1= second

call, 2-6 = after ring No. 2

- No.6

disabled

Remote access code (8 digits)

0 7

xxxxxxxx

any 8 digits code

00000000

10.1. Reaction to an incoming call sequence: 05

This sequence sets how the communicator will react to incoming calls on the telephone line. This setting is important for

access from a remote computer.

0 5 x

x can be 0 - never answer

1 - answer after second call = after 1 or 2 rings are detected, there must be a pause of 10 - 45 sec-

onds. The dialer will then answer on the very first ring of the second call. This setting can be used

to bypass an answering or facsimile machine connected to the same line. This “Second Call” fea-

ture is supported by the Comlink software

2, 3, 4, 5, 6 - answer after 2

, 3

, 4

, 5

or 6

ring

Note: Remote access connection can also be enabled by the alarm system user (regardless of the above setting) by en-

tering code 89 during service or user mode, when a remote call rings. If you use another telephone set on the same tele-

phone line, it should be switched to a tone dial mode.

Factory setting: 0 = never answer

10.2. Remote access code setting sequence: 07

In order to access the panel from a remote computer or JA-60E keypad, it is necessary to authorize the access with an 8-

digit access code. This code is compared with the one programmed in the control panel. If the remote computer tries to

access the panel with an other code, the connection will be terminated immediately and a wrong code alarm will triggered

on the control panel. Store your access code to the control panels by entering:

0 7 xxxxxxxx

x x . . . . . x - any 8 digits access code

Factory setting: 00000000

11. Factory default RESET

If you forgot the control panel codes or you have a control panel which is currently not under factory default setting, per-

form the following procedure:

• disconnect the AC adapter, back up battery and wait 30 seconds.

• reconnect the back up battery and close the control panel cover

• press and hold the 6 key on the control panel while reconnecting the AC adapter.

• when “−“ is displayed, enter 060 (within 10 seconds)

• reset is confirmed with “P” (panel is in programming mode)

Note: this procedure resets the factory default settings (see table 8). The Master code will be 1234, Service code 6060

and all user codes, detectors, controllers and other enrolled items will be forgotten. All telephone numbers will be erased.

The reset will not erase event memory and information about the reset will be recorded there.

Warning: if the Master code is forgotten when reset is disabled (with sequence 280 - see part 8.9.), the control panel re-

set will be possible only by the manufacturer.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60

Jablotron JA-60 Additional guide - English - 1 pages

Jablotron JA-60 User Manual - English - 6 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-60 Manual

Product: