555054
24
Zoom out
Zoom in
Previous page
1/34
Next page
12.2. Account code setting sequence: 02
This sequence is used for the alarm system identification by a Monitoring Station. The sequence structure is as follows:
02 x x x x
xxxx – account code ( x are numbers from 0 to 9 or hexadecimals).
When using only three-digit codes (formats 3/1 and 3/2) enter a zero in the first position. The communicator will then ig-
nore it (example - 0123)
Note: Changing of the account code erases the internal communicator’s memory of non reported events and sends a „Reset“ reporting
code (051) to the Monitoring Station.
Factory setting: 0000
12.3 Protocol and Format setting sequence: 03
This sequence is used to select the communication protocol and format. Its structure is as follows:
03 x y
x - protocol (0 – 9, see table bellow)
y - format (0 - 3 see table on right
)
Formats
y
format reports
structure
0
3/1
Major events only
xxx R
1
3/2
All events
xxx rc
2
4/1/1
Major events with autom.
source identification
xxxx Rn
3
4/2
All events
xxxx rc
xxxx = account number
R = major event code (first digit counts only)
rc = detailed event code (two digits)
n = source identification (generated automatically)
Surgard protocol has structure: xxxx E rc, where
E is a group identifier (generated automatically)
EEvent Note
1Fire
2 Panic
3 Alarm General
4 Arming Incl. Partial
5 Disarming
6 Failure Mains failure, RF jamming etc..
8 Report Enter/Exit service mode …
9 Restore End of alarm, panic …
A Test 24 hour test
Protocols
x Name
Hand-shake Data Kiss off Speed
format
0
Ademco Slow
(Si-
lent Knight)
1400Hz 1900Hz 1400Hz 10bps Next
table
1
Ademco Fast
1400Hz 1900Hz 1400Hz 14bps Next
table
2
Telemax
2100Hz 1650Hz 2100Hz 10bps Next
table
3
Franklin
2300Hz 1800Hz 2300Hz 20bps Next
table
4
Radionics 2300
2300Hz 1800Hz 2300Hz 40bps Next
table
5
Radionics 1400
1400Hz 1900Hz 1400Hz 40bps Next
table
6
DTMF 2300
2300Hz DTMF 2300Hz DTMF Next
table
7
Surgard*
2300Hz DTMF 2300Hz DTMF 4/3
8
Ademco express*
Dual tone DTMF 1400Hz DTMF 4ID/2
9
Contact ID*
Dual tone DTMF 1400Hz DTMF CID
* fixed format, “y” is arbitrary (0 is recommended)
Notes:
1/ Some Monitoring Station receivers do not support all formats.
2/ Logic of the format marking - 4/2 means, that an account code has
4 digits and an event report code has 2 digits.
Changing of a format erases the internal communicator’s memory of non reported events and sends a „Reset“ reporting code (051) to the
Monitoring Station.
Factory setting: 90 (Contac ID)
12.4. Re-dialing pause setting sequence: 04
If a dialer is triggered it attempts to make a connection (altering the main and the backup telephone number). If it is not
possible to make a connection after 8 attempts, a pause is inserted. After this pause the dialer dials again. If any event
triggers the communicator during the pause, the pause ends immediately. The pause length can be set in a following
way:
0 4 x
x – time multiplied by 10 minutes (from 1 to 9, example 3 = 30 minutes)
Factory setting: 1 = 10 min.
Alarm system JA-60 "COMFORT" - 24 - MDY51319
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60

Jablotron JA-60 Additional guide - English - 1 pages

Jablotron JA-60 User Manual - English - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info