Manual Jablotron JA-60 (page 23 of 34) (English)

555054

Zoom out

Zoom in

1/34

Alarm system JA-60 "COMFORT" - 23 - MDY51319

12. Monitoring station communication setting

This part of the manual is intended only for the use of specialists involved in monitoring. We recommend to use a com-

puter equipped with Comlink program for complete setting of the monitoring station communication (see 14). Changes of

the setting can also be performed manually using the JA-60E or built in keypad of the JA-60 system:

• Enter the programming mode (entering F 0 SC - SC = Service Code, factory default SC=6060), indicated by a „P“ on the display.

• To exit the programming mode, press the N key („P“ will turn off).

Monitoring station communication parameters

Sequence Description Factory default setting

0 001 xx

0 198 xx

Reporting codes table (see part 13)

where: x= 0 – 9, F0 = A

, F1 = B

, F2 = C

, F3 = D

, F4 = E

, F5 = F

if 00 is set, the event is not reported

For all events

0 2 xxxx

Account code (4 digits, for 3/1 and 3/2 formats the structure is 0xxx)

x = 0 – 9 (hexadecimal codes can be used too - see above)

0000

0 3 xy Protocol x:

0 = Ademco Slow

1 = Ademco Fast

2 = Telemax

3 = Franklin

4 = Radionics 2300

5 = Radionics 1400

6 = DTMF 2300

7 = Surgard

8 = Ademco Express

9 = Contact ID

Format y:

0 = 3/1 (xxx R)

1 = 3/2 (xxx rc)

2 = 4/1/1 (xxxx Rn)

3 = 4/2 (xxxx rc)

Contact ID

0 4 x Re-dialing pause, x= 1 – 9 (x 10 min.)

1 10 minutes

0 6 xx..xFy Phone numbers xx...x to memory y (1 and 2), pause = F0

erased

0 9 6060

Communicator reset to factory default settings

Dialing method ( tone / pulse) and telephone line checking has a common setting with the voice & Pager message setting - see part 9.4. and 9.6.

Notes:

Some of the protocols are not standardized

and some manufacturers of Monitoring Station

receivers use different parameters in some of

their protocols. Therefore Jablotron cannot

guarantee full compatibility with all Monitoring

Station receivers.

If the connection with the Monitoring Station is

not available, the events are queued in the

communicator’s memory and are transmitted in

one burst as soon as the connection is estab-

lished. All events are reported to the Monitoring

Station in the same order as they happened.

Once communication has started, it can not

be interrupted unless the control panel is

switched to the programming or to the user

mode. For example, if the user causes a false

alarm and then cancels it, both events are sent

to Monitoring Station.

Events occurring while the JA-60 control

panel is in a programming or user mode are

reported to the Monitoring Station after the

closing of these modes. (They are stored in the

memory and reported together with reporting

codes describing the change of operation

modes.)

When the dialer is activated, the communi-

cation to the monitoring station has the highest

priority (voice and Pager messages are sent

later with lower priority). A User or Installer can

interrupt the digital dialer communication by

entering the User mode or Programming mode.

Reset of the control panel has no influence to

the digital communicator’s settings (it is reported

to the Monitoring station as an event).

The RESET of the digital communicator it-

self (sequence 0 9 6060), the change of the

Monitoring Station’s telephone numbers, the

change of an account number code or the

change of a format setting will erase all the

reporting codes queued in the communicator’s

memory. However the events remain stored in

the control panel’s internal memory.

12.1. Reporting code setting sequences: 00 and 01

These sequences can be used to program the reporting codes for all possible events. Depending on the used protocol

and format, different amounts of data should be entered. The complete report codes programming table is shown in sec-

tion 13. The setting sequence structure is as follows:

0 x x x r c

xxx = event number (from 001 to 198)

rc = report code (two digits). For 3/1 and 4/1/1 formats only the first digit of the reporting code is

used (R). Codes should be entered in a hexadecimal format, with numbers higher than 9

beginning with the F key: A

= F0 B

= F1 C

= F2 D

= F3 E

= F4 F

= F5

If the reporting code 00 is programmed, the event will not be reported to the Monitoring Station.

Factory setting: 00 for all events

Notes:

• Abbreviation "Rc" is used in the report codes programming table for the major events group. Only the first digit of this group of codes is

transmitted when formats 3/1 or 4/1/1 are used. Other formats use both digits of the "Rc" and "rc" report codes.

• The Contact ID (CID) is an automatic protocol. If you enter any report code other than zero for a major event (Rc), all events of this type

will be transmitted automatically including all details regarding the event source. Internal structure of the CID protocol is shown in the

part 13.1. This protocol provides the most in-depth data for the monitoring station and its use is recommended by Jablotron.

• The Surgard protocol has 4/2 structure plus one more digit which is generated automatically (see 12.3.)

• The pulse formats are not capable to report zone numbers above 15. For this reason events in zone 16 or in a subsystem are reported

to the Monitoring Station as events in zone 10. This means that from the point of view of the monitoring station zone 10 also covers

zone 16 and the subsystem if used. This problem does not exist in the CID protocol.

• If the control panel is split and only one section is armed, then a partial arming report code is sent. If all sections are armed, a complete

arming report code is sent. If the system was completely armed and only one section is disarmed, will be sent the partial arming report

code.

• If the system is arming while there is a bypass, partial arming will be reported to the CMS (also stored to the internal memory)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60

Jablotron JA-60 Additional guide - English - 1 pages

Jablotron JA-60 User Manual - English - 6 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-60 Manual

Product: