555054

Jablotron JA-60 Manual

20
Zoom out
Zoom in
Previous page
1/34
Next page
Alarm system JA-60 "COMFORT" - 20 - MDY51319
Note: enter a pause (F0) after the last digit of a number which is calling a mobile phone. This way the number will be
called only once and the dialer will not check the line signals (some mobile phone systems do not generate standard
telephone line signals).
When activated, the dialer will disengage all other devices hooked up to the phone line (telephone, fax..). It will then,
one by one, call and play the user recorded message, for all programmed numbers. If the dialer makes a successful
connection to a programmed number, it will not call that number again. If the number is busy, the dialer will make 3 more
attempts to call it.
Empty tel. number memories are skipped. If all memories are empty, the dialer is completely disabled.
To delete a telephone number enter:
7 F0 Fy
where y is a memory number from 1 to 4
entering 7 F0 F0 will erase all tel. numbers, including the Pager number
Store number to call Pager (to memory number 5) entering:
7 xx..x F9 zzz....zz F5
where xx...x = provider prefix
F9 = separator (it will wait for a provider’s signal and will switch to DTMF if not used)
zzz...zz = pager number and numeric message and other specific codes (language selec-
tors, end of message etc.) if requested by the Paging provider
F5 = to store the number to memory no. 5
As a maximum 32 digits can be stored to memory # 5. Special characters can be entered with the following Fx codes:
pause
F0
∗
F7
#
F8
Example: enter 7 0611 F9 1 1234 555 F80 F5 if the provider prefix is 0611, the Pager number 1234 and the message
555. Number 1 after F9 is a language selector, code F80 represents #0 = end of message.
Note: some Paging providers also offer an option to send the message as an SMS to the GSM network. Consult your
Paging provider for details if you have trouble sending a message to the Pager.
To delete the Pager number enter:
7 F0 F5
If the memory number 5 is empty, no message will be sent to a Pager.
Factory default setting: all memories from 1 to 5 are empty.
9.2. Voice message recording sequence: 8 0
Press shortly key 8 then press key 0 and hold it pressed while talking into the control panel’s front grid (max. 20 sec-
onds). After releasing the 0 key, the message will play back. The message is stored in non-volatile memory and can be
changed when ever you want to by repeating the above steps. Make the message clear and brief. The dialer repeats the
message to each called number for 40 seconds.
It is possible to split the voice message into two different messages (10 seconds each). Depending on the setting in
section 9.5., a particular message will be sent under different situations.
If you want to record two messages: press shortly key 8 and then press key 1 and hold it pressed while recording the
first message. To record the second message press shortly key 8 then press key 2 and hold it pressed while talking into
the control panel’s front grid.
9.3. Telephone dialer testing sequence: 8 9
Enter 89 and the dialer will call the programmed numbers once. You will hear the telephone line signals from the built in
speaker during the test (if the dialer is triggered by an alarm in normal operation, it will call silently). Testing can be termi-
nated with the N key.
If two different voice messages were recorded, then use sequence 88 to test the sending of the first message and 89 to
test the sending of the second message.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60

Jablotron JA-60 Additional guide - English - 1 pages

Jablotron JA-60 User Manual - English - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info