555054
19
Zoom out
Zoom in
Previous page
1/34
Next page
Alarm system JA-60 "COMFORT" - 19 - MDY51319
8.28. New service code setting sequence: 5 nSC nSC
The Service Code can be used to enter the programming mode. A new Service Code must be entered twice in the se-
quence to avoid an error.
To change the code enter:
5 nSC nSC
where nSC is your new Service Code (four digits)
Example: to change service code to 1276 enter: 5 1276 1276
Factory default setting: service code is 6060
8.29. User Mode entering Sequence: 6 9 9 9
This sequence is used to switch from the Service Mode to the User Mode, where you can set zones´ bypass (see User´s
manual). You can exit the User Mode by pressing the “N” button. The bypassed zones will remain active after the leaving
the User Mode.
9. Voice & Pager messages setting
A control panel equipped with a telephone dialer can automatically send a voice message(s) and a code to a Pager. The most conven-
ient programming of the dialer is via a connected PC using the Comlink software (see 14). Programming can also be performed by
entering programming sequences from the system keypad while in the control panel programming mode:
Enter the programming mode (entering F 0 SC - SC = Service Code, factory default SC=6060), indicated by a „P“ on the display.
This can only be done while the panel is disarmed.
The parameters of the dialer can be set by entering programming sequences from the keypad. Any unfinished programming se-
quence can be terminated by pressing the N key.
To exit the programming mode, press the N key („P“ will turn off). If any fault is indicated when you try to exit the programming
mode, the control panel will inform you about the problem (see 8.20.).
Telephone numbers and the voice message can also be set up in the User Mode when enabled (see 8.6.2.)
List of the voice & Pager programmable parameters
Function sequence options
factory d.
note
Dialing method
90x
901 = tone 900 = pulse
tone
Triggering of the dialer with a Panic alarm
91x
911 = YES 910 = NO
911
Triggering of the dialer with an Intruder alarm
92x
921 = YES 920 = NO
921
Triggering of the dialer with a Fire alarm
93x
931 = YES 930 = NO
931
Triggering of the dialer with a Tamper alarm
94x
941 = YES 940 = NO
941
Triggering of the dialer with a Technical alarm
95x
951 = YES 950 = NO
951
Telephone line checking enabled
99x
991 = YES 990 = NO
NO
Store telephone numbers for voice message
7xx..x F y
xx...x = tel. number, y = mem-
ory 1 to 4, pause = F0
Pager dialing programming
7x.xF9z..zF5
x..x = provider tel. number z..z
= pager number + message
1:
2:
3:
4:
5:
Erase telephone number
7F0Fy
y = memory 1 to 5, entering
7F0F0 erases all
Record voice message
8 0 (hold 0 and talk to control panel)
2 messages - see 9.2.
9.1. Telephone numbers entering sequence: 7xxx....xxFy
Store telephone numbers for voice message entering:
7 xx... xx F y
where xx...xx = telephone number
y = memory number from 1 to 4
A telephone number can have a maximum of 16 digits. A pause can be entered with F0 (pause can not be entered as the first
digit).
Example: to store tel. number 483 123456 to memory no. 2 enter: 7 483 F0 123456 F2
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60

Jablotron JA-60 Additional guide - English - 1 pages

Jablotron JA-60 User Manual - English - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info