555054
8
Zoom out
Zoom in
Previous page
1/34
Next page
5. Testing of detectors and controllers
The control panel should be in the programming mode for testing – (LED display will show „P“ )(see part 8. how to enter
programming mode). If the control panel will not indicate a detector’s triggering during testing, it means that this detector
was not enrolled (see note in part 4.1.).
5.1. JA-60N magnetic door detector testing
Attach the detector’s cover (the detector will automatically enter a testing mode for 5 minutes)
Opening and closing of the door/window will be confirmed by the detector’s LED.
The control panel’s LED display will display the triggered detector’s number and it will make a beep - press F to select the
loudness of the beep (0-I-II).
5 minutes after the cover was attached, the detector will enter its normal mode and its LED indicator will be switched off
(battery energy saving function). Open and close the detector‘s cover to reset the testing mode for an additional 5 min-
utes, if needed.
5.2. JA-60P motion detector testing
Attach the detector's cover and wait until the LED turns off. From this moment the detector will be in its testing mode for 5
minutes and each detected movement will be confirmed by the detector's LED.
The control panel's LED display will display the triggered detector's number and it will make a beep - press F to select the
loudness of the beep (0-I-II).
Confirm that the detector covers the protected area as you expected (see diagram in fig. 11). If you need another cover-
age pattern (long corridor, pet zone), you can get an optional detector lens from your distributor.
5 minutes after the cover was attached, the detector will enter its normal mode and its LED indicator will be switched off
(battery energy saving function). Open and close the detector's cover to reset the testing mode for an additional 5 minutes
if needed.
fig. 11
Note: the motion detector, in normal operating mode, conserves battery energy. It will not indicate triggering with its
LED. It will also block the movement sensor for a period of 5 minutes after a movement is detected. This means that
when users are in the protected area and they move frequently in front of the detector, it will transmit information about
the movement to the control panel only once every 5 minutes. But when the users leave the area, the detector will be
ready for instant detection 5 minutes after the last triggering. This system significantly prolongs the life time of the batter-
ies.
To change the period, for which the sensor is blocked after triggering from 5 min. to 1 min., press and hold the detector’s
tamper switch when you install the batteries into it. This mode is suitable when you prefer more frequent transmissions of the
signal. However, the life time of the batteries will usually be shorter, depending on how frequently the detector is triggered.
5.3. Remote control and keypad testing
Alarm system JA-60 "COMFORT" - 8 - MDY51319
Press any button on the remote control (panic button) or enter a valid
code on the wireless keypad (1234 factory default setting)
The control panel’s LED display will display the controller’s number (c1 to
c8) and it will beep - press F to select the loudness of the beep (0-I-II).
This procedure allows you to test the remote control’s working range
The wire operated keypad, JA-60E, has identical functions as the con-
trol panel’s keypad.
Fig.12
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60

Jablotron JA-60 Additional guide - English - 1 pages

Jablotron JA-60 User Manual - English - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info