658894
37
Zoom out
Zoom in
Previous page
1/98
Next page
TXG237
36
Restarting Warm Engine
When restarting an engine that is still warm from pre-
vious use, the same procedure is used as with “Normal
Starting” except step No.6 may be omitted. Use of
glow plugs is not necessary when starting a warm
engine.
Cold Weather Starting
Procedure for starting an engine in colder ambient
temperatures is identical to “Normal Starting” proce-
dure except for the following:
1. Longer use of glow plugs may be required. Instead
of the normal 5-10s, main switch may need to be
selected to “glow” for 10-20s to adequately warm
engine combustion chambers.
2. At temperatures below 4°C (39°F) use of No.1
(No.1-D) diesel fuel is recommended due to pos-
sible “fuel gelling” characteristics of No.2 (No.2-D)
fuel at cold ambient temperature.
3. The central hydraulic reservoir in addition to trans-
mission and center housing lubrication, will require
additional warm-up time due to colder (thicker) oil.
Refer to “Warm-Up Period” at right.
4. Test all controls (steering, braking, etc) prior to op-
erating the tractor.
NOTE: Installation of accessory engine block heater
is recommended in cold weather conditions.
Consult your ISEKI Dealer.
IMPORTANT: Under no circumstances should either
or other starting fluid be used to start
engines equipped with glow plugs. Se-
vere engine damage will result should
starting fluid contact a hot glow plug.
If, for some reason, a booster battery is required to
start Tractor, ensure booster battery is connected
in parallel. When using booster battery and booster
cables always connect positive (+) terminals together
first. Then install booster cable on booster battery
negative (-) terminal and ground final booster cable
end on Tractor away from Tractor battery.
Warm-Up Period
After starting a cold engine, let engine idle at slow
speed to make sure all engine components are lu-
bricated. In colder ambient temperatures, extended
warm-up will be required to also warm hydraulic fluid
and lubricate drive line components. Suggested warm-
up period:
TABLE 2
Ambient Temp. Warm-Up Time
°C °F
0° & up 32° & up 5 to 10min.
0° to -10° 32° to 24° 10 to 20min.
-10° to -20° 24° to -2° 20 to 30min.
-20° & less -2° & less 30min. or more
IMPORTANT: Improper warm-up can result in:
Severe engine damage
Hydraulic pump seizure
Drive line bearing /gear damage
Sluggish steering /braking
CAUTION: Make sure parking brake is
securely applied and all controls are in
neutral while warming unit. Do not leave
unit unattended.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Iseki TXG237 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Iseki TXG237 in the language / languages: English as an attachment in your email.

The manual is 10,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info